Scag Power Equipment STT-31BSG manual General Information, Introduction, Direction Reference

Page 5

Section 1

GENERAL INFORMATION

1.1 INTRODUCTION

Your mower was built to the highest standards in the industry. However, the prolonged life and maximum efficiency of your mower depends on you following the operating, maintenance and adjustment instructions in this manual.

If additional information or service is needed, contact your Scag Power Equipment Dealer.

We encourage you to contact your dealer for repairs. All Scag dealers are informed of the latest methods to service this equipment and provide prompt and efficient service in the field or at their service shop. They carry a full line of Scag service parts.

USE OF OTHER THAN ORIGINAL SCAG REPLACEMENT PARTS WILL VOID THE WARRANTY.

When ordering parts, always give the model and serial number of your tractor. The serial number plate is located where shown in Figures 1-1.

SERIAL NUMBER

PLATE LOCATION

 

 

 

MORE

 

 

 

 

 

OR

 

 

 

 

PATENTS:

 

 

 

 

ONE

 

 

 

UNDER

 

 

 

FOLLOWING

 

 

 

MANUFACTURED

 

PENDING

 

 

THE

 

 

 

.

OF

 

PATENTS

 

 

 

 

 

 

 

 

 

 

 

Inc

 

 

 

 

 

ofMayville,53050

 

 

 

 

 

Pending

 

 

 

 

MetalcraftWisconsin

 

 

 

 

 

and

 

 

 

MODEL

of

Issued

 

 

 

Mayville,

 

 

 

 

SERIALDivisionPatents

For pictorial clarity, some illustrations and figures in this manual may show shields, guards or plates open or removed. Under no circumstances should your mower be operated without these devices in place.

All information is based upon product information available at the time of approval for printing. Scag Power Equipment reserves the right to make changes at any time without notice and without incurring any obligation.

1.2 DIRECTION REFERENCE

The “Right” and “Left”, “Front” and “Rear” of the machine are referenced from the operator’s right and left when seated in the normal operating position and facing the forward travel direction.

1.3SERVICING THE ENGINE AND DRIVE TRAIN COMPONENTS

The detail servicing and repair of the engine, hydraulic pumps and gearboxes are not covered in this manual; only routine maintenance and general service instructions are provided. For service of these components during the limited warranty period, it is important to contact your Scag dealer or find a local authorized servicing agent of the component manufacturer. Any unauthorized work done on these components during the warranty period may void your warranty.

390S0137

Figure 1-1 Tractor Serial Number Plate Location

1

Image 5
Contents OPERATOR’S Manual Remember Your Mower is only AS Safe AS the Operator Table of Contents Table of Contents Contd Introduction General InformationDirection Reference Servicing the Engine and Drive Train ComponentsISO Symbols Fast Slow Before Operation Considerations Safety InformationSignal Words Operation Considerations Before Operation Considerations ContdOperation Considerations Contd Maintenance ConsiderationsForward Reverse Drive System EngineEngine Deck Specifications Controls and Instrument Identification Operating InstructionsSafety Interlock System Forward Travel Starting the EngineGround Travel and Steering Engaging the Deck Drive Cutter Blades Reverse TravelAfter Operation Hillside OperationParking the Mower Recommendations for Mowing Removing Clogged MaterialMoving Mower with Engine Stopped Deck Release Lever Adjusting Cutting HeightCondition Cause Cure Troubleshooting Cutting ConditionsScalloped Cut, or Rough Contour Troubleshooting Contd Condition Cause CureGround Troubleshooting ContdTravel Adjustments AdjustmentsParking Brake Adjustment RH Steering Control Rod Adjustment Neutral AdjustmentThrottle Control and Choke Adjustments Tracking AdjustmentBelt Adjustment Belt AlignmentCutter Deck Pitch Cutter Deck AdjustmentsCutter Deck Level Cutter Deck Height Cutter Deck Height AdjustmentMaintenance Chart Recommended Service Intervals MaintenanceLubrication Grease Fitting Lubrication Chart see Figure Maintenance Chart Recommended Service Intervals ContdLubrication Fitting Points Changing Hydraulic Oil Hydraulic SystemChecking Hydraulic Oil Level Changing Hydraulic Oil Filter Element Engine OILChecking Engine Crankcase Oil Level Changing Engine Crankcase OilEngine Fuel System Engine AIR CleanerBattery Battery Electrolyte First AID Charging the BatteryDrive Belts Jump StartingBlade Sharpening Cutter BladesTires Blade ReplacementChecking Lubricant Level Cutter Deck GearboxCooling System Checking Coolant LevelBODY, DECK, and Upholstery Cleaning the Radiator Debris ScreenChecking The Fan Belt Tension 61A, 72A Cutter Decks Ref. Part Description Cutter Deck Controls Part Description Sheet Metal Components Ref. Part No. No Description Deck Drive Components Ref. Part Description RADIATOR, Coolers & Engine Brackets Ref. Part No. No. Description Brake and Steering Components Ref. Part Description Fuel and Hydraulic System Elbow, 90 Degree-1/4 NPT x 3/8 Hose Electrical System Ref. Part No. No. Description Hydraulic Pump Assembly BDP-21L Housing Kit Includes Housing, Journal Bearing Wire HARNESS, STT 31BSG Part Number Heavy-Duty 481588 481937 Limited Warranty Commercial Equipment 2000
Related manuals
Manual 64 pages 352 b