RedMax PSZ2460S manual Set up

Page 10

PSZ2460S

6. Set up

SE1

SE2

MOUNTING ENGINE (SE1)

1.Push the driveshaft housing toward the clutch housing and rotate it by hand to check that the driveshaft is engaged with the gears.

2.Insert the driveshaft housing into the clutch housing until it bottoms, and align the positioning holes on the both housings and install the screw.

3.Fasten the clamp securely with 2 screws.

CONNECTING THROTTLE WIRE

1. Remove the air cleaner cover.

2. Connect the end of the throttle wire to the joint on the top of the carburetor. (SE2)

CONNECTING SWITCH WIRES

Connect the switch wires between the engine and the main unit. Pair the wires of the same color.

SE5

SE6

WARNING

The saw chain has very sharp edges. Use protective gloves for safety.

1.Loosen a nut and remove the chain cover.

2.Mount the guide bar then fit the saw chain around the bar and sprocket.(SE5)

WARNING

Pay attention to the correct direction of the saw chain

3.Fit the chain tensioner nut into the lower hole of the guide bar, then install the chain cover, and fasten the mounting nut to finger tightness. (SE5)(SE6)

U S

SE3

(1)

(2)

(3)

(4)

(5)

ATTACHING THE PRUNING

MECHANISM (SE3)

1.Remove the cap on the end of the main pipe.

2.Remove the screw screwed into the end of the gear case.

3.Insert the end of the gear case into the main pipe.

4.Line up the hole on the end of the gear case into which the screw is to be inserted with the hole on the main pipe, and screw the screw firmly in.

5.Using a wrench, screw in the bolt provided to fix the mechanism into place.

(1)Main pipe

(2)Gear case

(3)Screw hole

(4)Fastening bolt

(5)Bolt

SE7

SE8

(1)Hole

(2)Moving direction

(3)Chain tensioner nut

4.Adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the bar rail.

(SE7)

(1)Chain tension adjusting screw

(a) Loosen

(b) Tighten

5.Tighten the mounting nut securely with the bar tip held up (SE8)(TORQUE: 8.9~11.7 N.m./90~120 kg-cm). Then check the chain for smooth rotation and correct tension while moving it by hand. If necessary, readjustment.

(1) Tighten

SE4

A standard package contains the items as shown below. (SE4)

(1)Guide bar

(2)Saw chain

(3)Gear case

(4)Sprocket

(5)Chain tension adjust screw

(6)Nut

(7)Chain tensioner nut

(8)Chain cover

Install the guide bar and the saw chain on the gear case as follows.

WARNING

It is very important to maintain the proper chain tension. Rapid wear of the guide bar or the chain coming off easily can be caused by improper tension. Especially when using a new chain, take good care of it since it should expand when first used.

BALANCE UNIT

1.Put on strap and attach unit to strap.

2.Depending on the working posture, slide clamp up or down until unit balances and the strap fits your body.

US-9

Image 10
Contents PSZ2460S PSZ2460S Contents Specifications Parts locationEmission Control Symbols on the machineManufactured Working Circumstance For safe operationWorking Condition Working PlanStarting the Engine Using the ProductMaintenance If Someone ComesHandling Fuel Kickback and Pinching Safety PrecautionsTransportation For safe operation Set up Fuel WarrantyFuel and Chain Oil Gasoline RequirementsFueling the Unit HOW to MIX Fuel Recommended Mixing Ratio Gasoline 50 OILFor Your Engine LIFE, Avoid Chain OILOperation Adjusting Idling Speed OP9 Adjusting OIL Flow RateAdjusting Throttle Cable OP8Maintenance MA8 Replacement Plug is a NGK CMR7HSAW Chain MA6Muffler Procedures to be Performed After Every 100 Hours of USETightening Torque Spark Arrester MA12Disposal Troubleshooting guideStorage Case 1. Starting failureWarranty Commencement Date Manufacturers Warranty CoverageOwners Warranty Responsibilities What is CoveredHOW to File a Claim Emission Warranty Parts ListWhat is not Covered Where to GET Warranty Service