Harman 286 Front Panel, Mic Preamp, AC Power, MIC Gain dB and Level dBu LEDs including Clip LED

Page 9

286s

Operating Controls

Section 2

To use the INSERT jack to MULT the preamp out (i.e., to provide an output with a buffered version of the signal after the Mic Preamp circuitry, but before the Processing Section), insert a Mono 1/4” plug fully into the INSERT jack, then pull the plug out one click. Plug the other end of the cable to the appropriate load. This will still allow the original signal path to continue to the Processing Section without interruption.

Note: If the plug is accidentally pushed fully into the INSERT jack, it will break off the connection between the Mic Preamp and Processing Sections; in this case, there would be no signal at the 286s LINE OUTPUT jack.

AC Power

Connect the AC power cord to the AC receptacle on the back of the unit. Route the AC power cord to a convenient power outlet away from audio lines. The unit may be turned on and off from a master equipment power switch.

2.2 Front Panel

Note: To reduce the risk of damage to your system, set the MIC GAIN control fully counterclockwise and lower your playback monitor levels before you connect a microphone, power on the unit, or press the PHANTOM button. This will eliminate spikes and surges, acoustical feedback, loud pops, momentary hiss, or other unwanted sounds.

Mic Preamp

MIC GAIN (dB) and LEVEL (dBu) LEDs (including CLIP LED)

Use this control to set the level of gain added to the microphone input signal (or a line-level input). Note that the 286s processing controls, or an external processor connected to the 286s INSERT, can provide additional gain. Try to set the MIC GAIN control so that you

do no have to reset it repeatedly; allow headroom for the maximum expected levels. For microphones (connected to the XLR MIC INPUT connector), the 286s can provide +0dB to +60dB of input gain. For line-level inputs (connected to the LINE INPUT jack), the gain is from -15dB to +45dB.

Note: To get the lowest noise possible from the 286s, set the input attenuators (if any) on your recorder or mixer for nominal levels (often about 3/4” of the way up or at the detent position; refer to the device’s operating manual). Then, set the 286s MIC GAIN so that your recorder or mixer is at its optimal operating level.

The red CLIP LED (located to the left of the MIC GAIN control) indicates that the combination

5

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Professional Audio Equipment Important Safety Information Electromagnetic Compatibility 286s Introduction Service Contact Info Warranty Rear Panel Operating ControlsFront Panel AC PowerMic Preamp MIC Gain dB and Level dBu LEDs including Clip LEDBypass Phantom Power Button and LEDHz Highpass Button and LED Process Bypass Button and LEDDe-Esser CompressorExpander/Gate EnhancerGain dB Control and Clip LED OutputConnecting the 286s to Your System Basic OperationUnderstanding the 286s Mic Preamp Processing Section Using the 286s as a Dedicated Mic PreampCompressor De-EsserExpander/Gate EnhancerUsing the Four Processors in Different Combinations OFF Suggested Settings/UsagesFemale Keyboard Guitar Bass Drums Strings ClubLF Detail HG Detail Noise Rushups, Hiss Buildup Problems, Possible Causes, SolutionsAudible Distortion Sound Cutting OffLispy Vocals Shrillness or Excessive BrightnessLow Rumble or Excessive Low Frequencies Technical Support and Factory Service Technical Specifications Enhancer Block Diagram 286s 286s

286 specifications

The Harman 286 is a significant advancement in the realm of audio technology, combining high-quality sound reproduction with innovative features tailored for both personal and professional use. Designed for audiophiles and casual listeners alike, the Harman 286 stands out due to its rich array of functionalities and elegant design.

At the heart of the Harman 286 is its advanced audio processing technology. It utilizes state-of-the-art digital signal processing (DSP) to deliver exceptional sound quality, ensuring that every note is crisp and clear. This high-resolution audio capability supports various formats, allowing users to enjoy music exactly as the artist intended. Additionally, the model features a robust, built-in amplifier that provides ample power while minimizing distortion, resulting in a dynamic listening experience.

One of the standout features of the Harman 286 is its wireless connectivity capabilities. Equipped with Bluetooth 5.0 technology, it facilitates seamless pairing with smartphones, tablets, and other compatible devices. This allows users to stream their favorite songs without the hassle of wires, enhancing convenience and portability. Furthermore, the Harman 286 supports various streaming services, providing users with access to a vast library of music at their fingertips.

The design of the Harman 286 reflects a modern aesthetic, making it a stylish addition to any space. With its sleek lines and premium materials, it not only sounds good but looks good too. The user-friendly control interface enables easy navigation through various settings and features, allowing users to customize their audio experience.

Another hallmark of the Harman 286 is its impressive battery life. Engineered for longevity, this model can provide several hours of continuous playback, making it ideal for both home use and on-the-go listening. When the battery does run low, the quick charge feature ensures minimal downtime, allowing users to get back to enjoying their music quickly.

In summary, the Harman 286 embodies a blend of cutting-edge technology, user-friendly features, and contemporary design. With its superior sound quality, versatile connectivity options, and long battery life, it remains a top choice for anyone seeking an exceptional audio experience. Whether for personal use or professional settings, the Harman 286 is a reliable companion for music lovers everywhere.
Top Page Image Contents