6.Do not store the machine and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F).
7.Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.
8.Be careful not to drop, shake or strike battery.
9.Do not charge inside a box or container of any kind. The battery must be placed in a well ventilated area during charging.
ADDITIONAL SAFETY RULES
FOR MACHINE
1.Be aware that this is always in an operating condition, because it does not have to be plugged into an electrical outlet.
2.Check the wheel carefully for cracks or dam- age before operation. Replace cracked or damaged wheel immediately.
3.Use only flanges specified for this machine.
4.Be careful not to damage the spindle, flanges (especially the installing surface) or bolt. Dam- age to these parts could result in wheel break- age.
5.Hold the machine firmly.
6.Keep hands away from rotating parts.
7.Make sure the wheel is not contacting the workpiece before the switch is turned on.
8.Wait until the wheel attains full speed before cutting.
9.Stop operation immediately if you notice any- thing abnormal.
10.Do not attempt to lock the trigger in the ``ON'' position.
11.Never attempt to cut with the machine held upside down in a vise. This can lead to serious accidents, because it is extremely dangerous. (Fig. 1)
12.Before setting the machine down after com- pleting a cut, be sure that the wheel has come to a complete stop.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge (Fig. 2)
·Always switch off the machine before insertion or removal of the battery cartridge.
·To remove the battery cartridge, pull out the set plate on the machine and grasp both sides of the cartridge while withdrawing it from the machine.
·To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before using the machine.
·Do not use force when inserting the battery car- tridge. If the cartridge does not slide in easily, it is not being inserted correctly.
Charging
For 4190D (Fig. 3)
1.Plug the battery charger into your power source.
2.Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the battery charger. Insert the cartridge fully into the port so that it rests on the charger port floor.
3.When the battery cartridge is inserted, the charg- ing light color will flash in red color and charging will begin.
4.When charging is completed, the charging light goes out. The charging time is as follows: Battery 7000, 7100, 7120, 9000, 9100, 9100A, 9120: approx. 60 minutes.
5.If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its ``trickle charge (maintenance charge)'' mode.
6.After charging, remove the battery cartridge from the charger and unplug the charger from the power source.
Battery type | Capacity | Number of | |
(mAh) | cells | ||
| |||
9000 | 1,300 | 8 |
CAUTION:
·The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer's batteries.
·When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times.
·When you charge a battery cartridge from a just- operated machine or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, let it cool off. Then
·When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, sometimes the charging light will go out soon. If this occurs, remove the battery cartridge and
5