Sears 247.77055 operating instructions Operation, Maintenance and Storage

Page 4

i.Never store the machine or fuel container inside where there is an open flame, spark, or pilot light (e.g. furnace, water heater, space heater, clothes dryer, etc.)

j.To reduce a fire hazard, keep machine free of grass, leaves, or other debris build-up. Clean up oil fuel spillage and remove any fuel soaked debris.

k.Allow machine to cool at least 5 minutes before storing.

OPERATION

1.Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet.

2.Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of all debris.

3.Thoroughly inspect all material to be shredded and remove any metal, rocks, bottles, cans, or other foreign objects which could cause personal injury or damage to the machine.

4.If the impeller strikes a foreign object or if your machine should start making an unusual noise or vibration, immediately shut the engine off. Allow the impeller to come to a complete stop. Disconnect the spark plug wire, ground it against the engine and perform the following steps:

a.Inspect for damage.

b.Repair or replace any damaged parts.

c.Check for any loose parts and tighten to assure continued safe operation.

5.Do not allow an accumulation of processed material to build up in the discharge area. This can prevent proper discharge and result in kickback of material through the feed opening.

6.Do not attempt to shred or chip material larger than specified on the machine or in this manual. Personal injury or machine damage could result.

7.Never attempt to unclog either the feed intake or discharge opening while the engine is running. Shut the engine off, wait until all moving parts have stopped, disconnect the spark plug wire and ground it against the engine before clearing debris.

8.Never operate without vacuum bag and discharge chute properly attached to the machine. Never empty or change vacuum bag while the engine is running. Rear end of vacuum bag must be kept closed at all times during operation.

9.Never operate without either the inlet nozzle or optional hose attachment properly attached to the machine. Never attempt to attach or change either attachment while the engine is running.

10.Keep all guards, deflectors and safety devices in place and operating properly.

11.Keep your face and body back and to the side of the chipper chute while feeding material into the machine to avoid accidental kickback injuries.

12.Never operate this machine without good visibility or light. Always be sure of your footing and keep a firm hold on the handles.

13.Do not operate this machine on a gravel surface.

14.Do not operate this machine while under the influence of alcohol or drugs.

15.Muffler and engine become hot and can cause a burn. Do not touch.

16.Never pick up or carry machine while the engine is running.

MAINTENANCE AND STORAGE

1.Never tamper with safety devices. Check their proper operation regularly.

2.Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage and repair, if needed.

3.Before cleaning, repairing, or inspecting, stop the engine and make certain the impeller and all moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

4.Do not change the engine governor settings or overspeed the engine. The governor controls the maximum safe operating speed of the engine.

5.Maintain or replace safety and instruction labels, as necessary.

6.Follow this manual for safe loading, unloading, transporting, and storage of this machine.

7.Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer, etc.

8.Always refer to the operator’s manual for proper instructions on off-season storage.

9.If the fuel tank has to be drained, do this outdoors.

10.Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Yard Vacuum Table of Contents WarrantyTraining SafetyPreparation Maintenance and Storage OperationRepair Protection Agreement Disconnecting Spark Plug AssemblyRemoving Unit from Carton Loose Parts in Carton See FigureAttaching the BAG Attaching The Hose AssemblyAttaching the Blower Chute Front Tab Locking Rod Nozzle Height Adjustment Lever Chipper ChuteNozzle BagTo Stop Engine GAS and OIL FILL-UPTo Start Engine To Empty BAG Using the Nozzle VacuumTo Remove Blower Chute Using the Hose Assembly Nozzle Height AdjustmentClean Equipment General RecommendationsCheck Engine OIL LubricationService AIR Cleaner Service Spark PlugService Muffler Clean EngineCarburetor Adjustment Service and AdjustmentsEngine Speed Removing the Flail ScreenDisconnect and ground the spark plug wire Sharpening or Replacing Chipper BladeYard Vacuum EngineOther StorageTroubleshooting Problem Possible Causes Corrective ActionParts List Part Description Sears Craftsman 6.0 H.P. Yard Vacuum Model 731-2294A Nozzle Door Contenido GarantiaOperacion EN General SeguridadNiños ServicioDesembalaje Piezas SueltasDesconexion DE LA Bujia Instalacion DEL ManillarInstalacion DEL Tubo DE Soplado Tolva de Controles DE Operacion OperacionGasolina Para Apagar EL MotorDescarga de la bolsa Para Arrancar EL MotorExtracción del canal de soplado Uso del montaje de la manguera Uso del pico de la aspiradoraAjuste de la altura del pico Recomendaciones Generales LubricacionLimpieza DEL Equipo Revision DEL Aceite DEL MotorPara Vaciar EL Aceite Servicio DEL Filtro DE AireServicio DE LA Bujia Servicio DEL SilenciadorAjuste DEL Carburador Velocidad DEL MotorRetiro DE LA Rejilla DE Flagelos Servicio Y AjustesAfilado O Reemplazo DE LA Cuchilla Astilladora Aspiradora para jardines MotorOtros AlmacenamientoProblema Causas posibles Solución Localizacion DE AveriasRepair Protection Agreements Get it fixed, at your home or ours

247.77055 specifications

Sears 247.77055 is a robust tool that combines a variety of features and technologies to meet the needs of both amateur and professional users. As part of Sears' commitment to quality and durability, this particular model is designed to provide reliable performance while ensuring ease of use.

One of the main characteristics of Sears 247.77055 is its powerful motor. The high-performance motor delivers consistent power across all tasks, whether cutting, drilling, or performing intricate jobs. It ensures that the tool can handle heavy-duty applications without straining or overheating, making it ideal for long-term use in demanding environments.

In addition to its robust motor, the Sears 247.77055 incorporates advanced safety features. These include an integrated safety switch that prevents accidental starts, as well as protective guards that shield users from debris and injury. Ergonomic design is a cornerstone of this model, ensuring that the grip is comfortable and minimizes fatigue during prolonged usage.

The tool also stands out for its versatility. It comes with multiple attachments and accessories, allowing users to switch between different tasks seamlessly. From sanding and grinding to polishing and drilling, the Sears 247.77055 can tackle a vast array of projects, enhancing its value for both DIY enthusiasts and professionals.

Another important feature of the Sears 247.77055 is its compact and lightweight design. This feature makes it easy to store and transport, providing convenience for users who may need to take their tools to job sites or move them around within their workspace. The tool’s streamlined construction does not compromise on power, ensuring that the tool remains effective without being cumbersome.

Sears has also integrated state-of-the-art technologies into the 247.77055. For instance, the tool incorporates advanced cooling systems that prevent overheating during extended use, maintaining performance and extending its lifespan. Additionally, features such as variable speed settings allow users to control the power output based on the specific requirements of the task at hand.

Moreover, the Sears 247.77055 is backed by a warranty, reflecting the company’s confidence in the product's durability and reliability. Overall, the combination of performance, safety, versatility, and user-friendly design makes the Sears 247.77055 a valuable addition to any toolkit, suited for both home improvement projects and professional applications alike.
Top Page Image Contents