Simplicity ZT2354, LC-9 manual Servicing the Mower Blades, Removing the Blade

Page 25

Regular Maintenance

SERVICING THE MOWER BLADES

1.Remove mower from the rider. See Mower Installation & Removal.

2.Blades should be sharp and free of nicks and dents. If not, sharpen blades as described in following steps.

3.To remove blade for sharpening, use a wood block to hold blade while removing the blade mounting cap- screw (Figure 24).

4.Use a file to sharpen blade to fine edge. Remove all nicks and dents in blade edge. If blade is severely damaged, it should be replaced.

5.Balance the blade as shown in Figure 25. Center the blade’s hole on a nail lubricated with a drop of oil. A balanced blade will remain level.

LOOSEN

Figure 24. Removing the Blade

6. Reinstall each blade with the tabs pointing up toward deck as shown in Figure 26. Secure with a cap- screw, spring washer and hex washer (be certain the

hex washer is aligned with the hex shaft). Use a wooden block to prevent blade rotation and torque

capscrews to 45-55 ft.lbs. (61-75 N.m.).

Nail

Figure 25. Balancing The Blade

WARNING

For your personal safety, blade mounting capscrews must each be installed with a hex washer and spring washer, then securely tightened. Torque blade mounting capscrew to 45-55 ft. lbs. (61-75 N.m.)

B

C

D

A

TIGHTEN

Figure 26. Installing The Blade

A.	4x4 Wood Block	C.	Spring Washer
B.	Hex Washer	D.	Blade Bolt

21

Image 25

Contents Paper Size Paper Size 11 xPress BinderyThis page Intentionally Blank OPERATOR’S Manual North Main Street Munnsville, NY 13409 Table of Contents Have These Numbers Identification NumbersIdentification Numbers General Operation Safety Rules InformationSlope Operation Do NotService and Maintenance Safety Rules & InformationChildren Transporting and StorageDo not put hands or feet Safety DecalsSeat Adjustment Lever Features & Controls Zero Turn RiderIgnition Switch Control FunctionsFeatures & Controls Operating Zero Turn Rider General Operating SafetyChecks Before Starting Starting the Engine Operating the Zero Turn RiderStopping the Rider MowingSmooth Travel Zero Turn Driving PracticeForward Travel Practice Reverse Travel Practice Practice Turning In Place Practice Turning Around a CornerExecuting an End-Of-Row Zero Turn Removing the Mower Deck Mower Deck Removal InstallationMower PTO Belt Routing Installing the Mower DeckStarting After Long Term Storage StorageTemporary Storage 30 Days Or Less Long Term Storage Longer Than 30 DaysPage Check Tire Pressures Regular MaintenanceSee Before Every Spring FallChecking / Adding Fuel Regular MaintenanceFuel Filter Grease LubricationSuspension Lubrication Checking the Battery Fluid Battery MaintenanceCleaning the Battery and Cables Removing the Blade Servicing the Mower BladesPage Troubleshooting the Rider Troubleshooting Adjustments & ServiceTroubleshooting the Mower Troubleshooting, Adjustment & ServiceGround Speed Control Lever Adjustment Seat AdjustmentSpeed Balancing Adjustment Suspension Height Adjustment Parking Brake AdjustmentBlade Brake Check PTO Clutch AdjustmentDampener Force & Neutral Spring Return Adjustment Neutral AdjustmentCutting Height Adjustment Mower AdjustmentsDeck Roller Adjustment Gauge WheelsMower Belt Replacement Hydraulic Pump Drive Belt ReplacementPTO Belt Replacement Mower Deck Arbor Drive Belt ReplacementCharging a Completely Discharged Battery Battery ServiceChecking Battery Voltage Troubleshooting, Adjustment & Service Page Lawn Care & Mowing Information Inch Lawn Care & Mowing InformationProper Cutting Height Cut Here On First Pass SecondWhen and HOW Often to MOW Mowing Methods Methods actually contribute to a healthy lawn Lawn Care & Mowing InformationStepped Cutting Solutions for Common Mowing ProblemsScalping Uneven CuttingStingers Technical Manuals Common International SymbolsLC-9