Battery Service, Checking the Battery Voltage

Battery Service

CHECKING THE BATTERY VOLTAGE

Keep open flames and sparks away from the bat- tery; the gasses coming from it are highly explo-

sive. Ventilate the battery well during charging.

A voltmeter can be used to determine condition of bat- tery. When engine is off, the voltmeter shows battery voltage, which should be 12 volts. When engine is run- ning, the voltmeter shows voltage of charging circuit which normally is 13 to 14 volts.

A dead battery or one too weak to start the engine may not mean the battery needs to be replaced. It may, as an example, mean that the alternator is not charging the battery properly. If there is any doubt about the cause of the problem, see your dealer. If you need to replace the battery, follow the steps under Cleaning the Battery & Cables in the Normal Care Section.

CHARGING A COMPLETELY

DISCHARGED BATTERY

1.Be aware of all the safety precautions you should observe during the charging operation. If you are unfamiliar with the use of a battery charger and hydrometer, have the battery serviced by your dealer.

A WARNING

Do not attempt to charge a frozen battery. Allow the battery to warm to 60” F (15.5” C) before plac- ing on charge.

2.Add water sufficient to cover the plate (fill to the prop- er level near the end of the charge). If the battery is extremely cold, allow it to warm before adding water because the water level will rise as it warms. Also, an extremely cold battery will not accept a normal charge until it becomes warm.

3.Always unplug or turn the charger off before attach- ing or removing the clamp connections.

4.Carefully attach the clamps to the battery in proper polarity (usually red to [+] positive and.black to [-]

negative).‘.

5.While charging, periodically measure the temperature of the electrolyte. If the temperature exceeds 125” F (51.6” C), or if violent gassing or spewing of elec- trolyte occurs, the charging rate must be reduced or temporarily halted to prevent battery damage.

6.Charge the battery until fully charged (i.e. until the specific gravity of the electrolyte is 1.250 or higher and the electrolyte temperature is at least 60” F). The

best method of making certain a battery is fully charged, but not over charged, is to measure the specific gravity of a cell once per hour. The battery is fully charged when the cells are gassing freely at low charging rate and less than 0.003 change in specific gravity occurs over a three hour period.

JUMP STARTING WITH AUXILIARY (BOOSTER) BATTERY

Jump starting is not recommended. However, if it must be done, follow these directions. Both booster and dis- charged batteries should be treated carefully when using jumper cables. Follow the steps below EXACTLY, being careful not to cause sparks. Refer to Figure 25.

1.Both batteries must be of the same voltage.

2.Position the vehicle with the booster battery adjacent to the vehicle with the discharged battery so that booster cables can be connected easily to the batter- ies in both vehicles. Make certain vehicles do not touch each other.

3.Wear safety glasses and shield eyes and face from batteries at all times. Be sure vent caps are tight. Place damp cloth over vent caps on both batteries.

4.Connect positive (+) cable to positive post of dis- charged battery (wired to starter or solenoid).

5.Connect the other end of same cable to same post marked positive (+) on booster battery.

6.Connect the second cable negative (-) to other post of booster battery.

7.Make final connection on engine block of stalled vehi- cle away from battery. Do not lean over batteries.

8.Start the engine of the vehicle with the booster bat- tery. Wait a few minutes, then attempt to start the engine of the vehicle with the discharged battery.

9.If the vehicle does not start after cranking for thirty seconds, STOP PROCEDURE. More than thirty sec- onds seldom starts the engine unless some mechani- cal adjustment is made.

lO.After starting, allow the engine to return to idle speed. Remove the cable connection at the engine or frame. Then remove the other end of the same cable from the booster battery.

11.Remove the other cable by disconnecting at the dis- charged battery first and then disconnect the oppo- site end from the booster battery.

12.Discard the damp cloths that were placed over the battery vent caps.

1693266, 1693264 specifications

Simplicity 1693264 and 1693266 are pioneering models in the realm of modern design and functionality, offering significant improvements over previous iterations. These models are particularly notable for their focus on user experience and efficiency.

One of the main features of the Simplicity 1693264 and 1693266 is their streamlined interface. Users will appreciate the intuitive design that allows for easy navigation and quick access to essential functions. This aspect is especially beneficial for those who may not be technologically savvy, as it minimizes the learning curve and enhances overall usability.

Both models incorporate advanced technologies that set them apart from competitors. The integration of a robust operating system ensures optimal performance, allowing for seamless multitasking and minimal downtime. Additionally, these models support modern connectivity options, such as Bluetooth and Wi-Fi, enabling users to connect various devices effortlessly. This feature is particularly valuable in an age where smart devices are increasingly prevalent.

Another characteristic of the Simplicity 1693264 and 1693266 is their commitment to sustainability. Manufactured with environmentally friendly materials, these models reflect a growing trend in the industry toward eco-conscious design. This not only appeals to environmentally aware consumers but also aligns with global efforts to reduce carbon footprints.

In terms of performance, both models boast impressive specifications that cater to a wide range of uses. Whether for home or office environments, they offer reliability and speed, making them ideal for both personal and professional applications. The inclusion of energy-efficient technologies further enhances their appeal, ensuring that users benefit from lower operating costs over time.

Moreover, the design aesthetic of Simplicity 1693264 and 1693266 is chic and modern, making them visually appealing additions to any space. Their compact size ensures that they can fit seamlessly into various settings, from small apartments to large offices.

In summary, Simplicity 1693264 and 1693266 stand out due to their user-friendly interfaces, advanced technologies, sustainable manufacturing practices, impressive performance capabilities, and modern design. These features make them worthwhile options for consumers looking for efficiency and style in their technological solutions.