HOW to Start Your Unit, Spark Plug | Poulan XT 200, XT 25, WT21

HOW TO START YOUR UNIT

Starting Position Choke Lever

Trigger
Primer Bulb	Muffler
	Muffler

WARNING: The trimmer head will turn while starting the engine. A hot muffler can cause serious burns.

COLD ENGINE STARTING OR STARTING AFTER REFUELING

SSet unit on a flat surface.

SSlowly press the primer bulb 6 times.

SMove choke lever to FULL CHOKE position. S Squeeze the throttle trigger fully and hold

through all remaining steps.

S Pull starter rope handle sharply 6 times. S Move choke lever to HALF CHOKE position. S Pull starter rope handle no more than 6

pulls, until engine runs.

S Allow engine to run 10 seconds, then move choke lever to OFF CHOKE position.

RESTARTING A WARM ENGINE

SMove choke lever to OFF CHOKE position. S Pull starter rope handle until engine runs. S If engine does not start in 5 pulls, follow instructions in STARTING A COLD ENGINE.

For occasional use only.

OPERATING POSITION

ALWAYS WEAR: Eye

Protection

Long Pants

Heavy Shoes

Cut from your right to your left.

ADVANCING THE CUTTING LINE

Advance line by tapping the bottom of the cutting head lightly on the ground while engine is running at full speed. A metal blade attached to the shield will cut the line to the proper length.

REPLACING THE LINE

S Remove spool by firmly pulling on tap button.

SClean entire surface of hub and spool.

S Replace with pre--wound spool, or cut a length of 18 feet of .065” (1.6 mm) diameter Weed Eater! brand line. Never use wire, rope, string, etc., which can break off and become a dangerous missile.

SInsert one end of line about 1/2 inch (1 cm)

into the small hole on the inside of the spool. S Wind line evenly and tightly onto spool.

Wind in the direction of the arrow on the spool.

SPush the line into the notch, leaving 3 to 5

inches ( 7 -- 12 cm) unwound.

SInsert the line into the exit hole in the hub as

shown in the illustration.

SAlign the notch with the line exit hole.

SPush spool into hub until it snaps into place. S Pull the line extending outside of the hub to

release it from the notch.

Small

HoleSpool

Line in Notch

Hub

Line exit hole

We recommend all service and adjustments not listed in this manual be performed by an Authorized Service Dealer.

CARBURETOR ADJUSTMENTS

Your carburetor is equipped with limiter caps. Adjusting the carburetor is a complicated task. We recommend that you take your unit to an Authorized Service Dealer. Damage will occur if you turn the needles beyond the limiter stops.

IGNITION TIMING

The ignition timing is fixed, non--adjustable.

SPARK PLUG

Replace the spark plug yearly using a Champion RCJ--8Y plug. Spark plug gap is

.025”.

XT 200, XT 25, WT21 specifications

The Poulan XT 200, XT 25, and WT21 are powerful machines tailored for homeowners and professionals looking for robust performance in outdoor maintenance. Each model boasts its unique features and technologies, making them versatile tools in lawn care and garden upkeep.

The Poulan XT 200 is a gas-powered trimmer known for its reliability and efficiency. Its lightweight design allows for easy maneuverability, making it an excellent choice for those challenging spots in your yard. The XT 200 is equipped with a 25cc two-cycle engine, which delivers substantial power without sacrificing fuel efficiency. Its Easy-Start system ensures that users can start the trimmer with minimal effort. The adjustable cutting width provides flexibility in handling different tasks, whether trimming tight corners or clearing larger areas.

Next, the Poulan XT 25 is another remarkable model that focuses on convenience and user comfort. It features a robust 25cc engine, similar to the XT 200, but comes with additional enhancements that make it a top choice for homeowners. One of its standout features is the dual-line automatic feed system, which releases cutting line as needed, allowing users to focus on the task without constant reloading. The XT 25 also includes an ergonomic handle design, reducing fatigue during extended use. Its lightweight construction makes it easy to handle, while the anti-vibration technology further enhances user comfort, particularly during long trimming sessions.

Lastly, the Poulan WT21 is a versatile and powerful blower designed for efficient cleanup of debris and leaves. It utilizes a 21cc two-cycle engine that delivers robust performance while remaining lightweight and easy to handle. The WT21 also features a variable speed trigger, providing users with complete control over airflow, whether they need a gentle breeze for delicate tasks or a powerful blast for tough debris. The ergonomic grip ensures comfort during extended operation, promoting ease of use for both novice and seasoned users.

In summary, the Poulan XT 200, XT 25, and WT21 stand out in their respective categories with impressive power, user-friendly features, and advanced technologies. Whether faced with trimming, edging, or blowing leaves, these Poulan models provide the durability and efficiency required to tackle any outdoor task effectively.