Lexicon Lambda Desktop Recording Studio owner manual Important Safety Instructions

Page 2

IMPORTANT SAFETY INSTRUCTIONS

The symbols shown above are internationally accepted symbols that warn of potential hazards with electrical products. The lightning flash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within the unit. The exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owner’s manual.

These symbols warn that there are no user serviceable parts inside the unit. Do not open the unit. Do not attempt to service the unit yourself. Refer all servicing to qualified personnel. Opening the chassis for any reason will void the manufacturer’s warranty. Do not get the unit wet. If liquid is spilled on the unit, shut it off immediately and take it to a dealer for service. Disconnect the unit during storms to prevent damage.

Safety Instructions

Notice For Customers If Your Unit Is Equipped With A Power Cord.

WARNING: THIS APPLIANCE MUST BE EARTHED. Connect only to a mains socket outlet with protective earthing connection.

The cores in the mains lead are coloured in accordance with the following code:

GREEN and YELLOW - Earth

BLUE - Neutral

BROWN - Live

As colours of the cores in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The core which is coloured green and yellow must be connected to the terminal in the plug marked with the letter E, or with the earth symbol, or coloured green, or green and yellow.

The core which is coloured blue must be connected to the terminal marked N or coloured black.

The core which is coloured brown must be connected to the terminal marked L or coloured red.

This equipment may require the use of a different line cord, attachment plug, or both, depending on the available power source at installation. If the attachment plug needs to be changed, refer servicing to qualified service personnel who should refer to the table below. The green/yellow wire shall be connected directly to the units chassis.

WARNING: If the ground is defeated, certain fault conditions in the unit or in the system to which it is connected can result in full line voltage between chassis and earth ground. Severe injury or death can then result if the chassis and earth ground are touched simultaneously.

WARNING FOR YOUR PROTECTION

READ THESE INSTRUCTIONS:

KEEP THESE INSTRUCTIONS HEED ALL WARNINGS FOLLOW ALL INSTRUCTIONS

Do not use this apparatus near water

The apparatus shall not be exposed to dripping or splashing liquid and no object filled with liquid, such as vases, shall be placed on the apparatus.

CLEAN ONLY WITH A DRY CLOTH.

DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS.

DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.

ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER.

UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or third prong are provided for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Use only with the cart stand, tripod bracket, or table specified by the manu- facturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

POWER ON/OFF SWITCH: For products provided with a power switch, the power switch DOES NOT break the connection from the mains.

MAINS DISCONNECT: The plug shall remain readily operable. For rack- mount or installation where plug is not accessible, an all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated into the electrical installation of the rack or building.

FOR UNITS EQUIPPED WITH EXTERNALLY ACCESSIBLE FUSE RECEPTACLE:

Replace fuse with same type and rating only.

MULTIPLE-INPUT VOLTAGE: This equipment may require the use of a different line cord, attachment plug, or both, depending on the available power source at installation. Connect this equipment only to the power source indicated on the equipment rear panel. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel or equivalent.

This Equipment is intended for rack mount use only.

Image 2
Contents Complete recording solution Important Safety Instructions Safety InstructionsProduct option Use only shielded interconnecting cablesProduct name Lexicon Lambda 1998Warranty Service Info/WarrantySerVice Info Result of the products use in any circuit or assemblyTable of Contents Section Title UsinG tHe LeXicon LamBDa StudioSpecifications SiGnaL routinG DiaGram Section Title Lambda Desktop Recording Studio proVides the following FeaturesIntroduction Lambda desktop audio interface hardware UnpacKinG tHe LamBDa StudioComputer minimum reQuirements Pentium III 500 MHz or AMD K7 processor, or betterFront PaneL Lambda Studio front panel offers the following featuresFront Panel Down a GainOutput LeVel +48V phantom power LEDMonitor MiX Control INput bargraph meterREAr PaneL Lambda Studio rear panel offers the following featuresRear Panel Adjust headphone volume with the Output Level knob MonitorinG connectionsAnalog inserts require a ¼ TRS to 2 x ¼ TSadapter cable. About Recording ConnectionsABout RecorDinG connections MiXDown Connections Connecting to an eXternal recorderMixdown Connections Connections Diagram Connections DiaGram WinDows Software setupMac OS Macintosh Software SetupMacintosH Software SetUp Under Devices, click on Using the Lexicon Lambda StudioOnce Cubase LE opens, go to Section I Recording audio With the Lambda Studio Recording Using the Microphone/Line InputRecording using the Microphone/line Input Recording Using the Microphone/Line Input Labeled as Audio Recording Using the Microphone/Line Input Recording Using the Microphone/Line Input Recording Using the Microphone/Line Input Labeled as Audio Recording a Guitar Using the Instrument Input Recording a Guitar using the Instrument inputRewind Recording Midi with the Lambda Studio Section II Recording Midi with the lambda studioClick the Track Edit button Using Software Input MonitoringSection III Using software Input Monitoring Click on an Insert Using Software Input Monitoring Section IV Adjusting the Buffer Settings Adjusting the Buffer SettingsOpen Cubase LE and go to DevicesDevice Setup Adjusting the Buffers in Windows XpWhen you are finished click OK Adjusting the Buffers in MAC osXSpecifications SpecificationsLambda Signal Routing Diagram Lexicon Lambda Studio Signal Routing DiagramLambda Desktop Recording Studio