Never store the engine with fuel in the tank in a poorly ventilated place where the fumes produced by the gasoline could propagate and
reach a fire, candle, burner or furnace pilot light, water heater, dryer, etc. Never store excessive quantities of fuel.
E. Assembly/disassembly
E1. Setting the motor on the frame
4
Position the motor so that the fuel cap faces upward and the bracket for fastening it to the frame is on one side. Screw pin A onto the motor as shown in the figure and tighten it securely. Fasten the motor to the frame and tighten it securely with the nut provided (B).
E2. Insertion of padding on frame
4
Pick up the frame+motor assembly and place them on the base; insert the upper part of the padding on the frame and fasten it with the two straps as shown in the figure. Take the support for the starter knob and fit it as shown in the figure. Fasten the starter cord to the support as shown in figure.
E3. Assembly of the transmission shaft to the
flexible shaft 4 
9
Pull the plastic ring nut away from the end of the rigid tube turning it counterclockwise if necessary. Insert the rigid tube into the handle section until the label is aligned with the edge of the plastic threaded rim Tighten the ring nut hand tight.
Safety pole guard
2 
3 
4
The safety pole guard should be mounted using the accessories supplied and in the configuration shown in the figure,in contact with the delta handle.
E4. Delta grip
4
For your safety, fasten the delta handle in front of the label placed on the shaft at a distance of at least 11 cm from the rear grip. The handle should be fastened in a comfortable working position. If you are using sawtooth blades, the grip distance should be moved by at least 36 cm.
E5. Fitting guard on line cutter head and grass cutting blade
2 
3 
4
Fit the safety guard (A) against the gearbox (I) position the lower clamp (G) in the housing under the shield and the upper clamp (F) over the shaft. Insert and tighten the screws (H).
Safety guard extension (exclusively for use with nylon string head)
2 
3 
4
The string cutting blade housed in the plastic shield will cut the nylon string to optimum length; a string that is too long reduces the rotation speed of the engine and interferes with cutting efficiency, as well as increasing the risk of injury.
The extension (B) should be installed only for use with the nylon string head, with the aid of the string cutter blade (L), that regulates the length of the string and thus the cutting diameter. For correct assembly see the illustration on the cover and perform the following sequence of steps: Insert the extension (B) on the safety guard (A) at the reference notches (C), and fasten with the screws (D), then apply the string cutter blade (L) with the cutting edge facing towards the outside of the shield, and fasten it with the screw (E) (Make sure the screws are tightened all the way (E) and are not loosened by the vibrations. If necessary, tighten them again).
E6. Assembly/disassembly of line cutter head
2 
3 
4 
10
Apply the nylon string head as shown in the illustration: a) Protection flange b) Upper plate c) Nylon string head. Tighten by turning counterclockwise. As you tighten, hold the nylon string head and plate still and insert the wrench or screwdriver supplied in the holes in the plate and gearbox; first turn the plate until the two holes match.
E7. Assembly/disassembly of grass cutter blade
2 
3 
4 
10
Do not use the nylon string head guard extension (H) with metal blades.
Assemble blade as illustrated: a) Flange guard -
b)Upper cap with blade centering - c) Blade with text and directional arrow facing upwards - d) Lower washer - e) Fixed mower gauge - f) Blade locking screw (length mm 16).
If you want to assemble the rotating mower gauge,proceed as illustrated: a) Flange guard -
b)Upper cap with blade centering - c) Blade with text and directional arrow facing upwards - d)