Fault Finding Chart
WARNING Disconnect from the mains electricity supply before attempting any maintenance or adjustment.
FAULT
LINE NOT FEEDING
OR
LINE TOO SHORT
OR
TRIMMER VIBRATES
CHECK
|
| Is the automatic line feed work- |
| No |
|
| ing? |
| |
|
|
|
|
|
|
|
|
|
|
|
| Is the line fed out and visible? |
|
|
|
|
| No | |
|
| Has line been removed from |
| |
|
|
| ||
|
| cleat? |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Is the manual line feed working? |
| No |
|
|
| ||
|
|
|
|
|
ACTION
Manually feed out line.
SEE “MANUAL LINE FEED”
Remove cap and spool, free line and
“CUTTING HEAD”
The line may be jammed on the spool. Rewind line to remove crossed loops. Check that line is in correct section of spool.
CONTINUOUS CLATTER-
ING NOISE
Is the motor up to speed before No use?
Has too much line been fed out? 
Yes
Is the line cutter missing from the Yes safety guard?
Allow the motor to reach operating speed before use.
SEE “MANUAL LINE FEED”
Contact your local approved Service Centre or Husqvarna UK Ltd. Customer Service.
LINE SNAPS CONTINU-
OUSLY
IF NONE OF THE ABOVE OR IF FAULT PERSISTS
|
| Are you using the trimmer cor- |
| ? |
| Only use tip of nylon line to trim. |
|
| rectly? |
|
| SEE “How to trim and edge” | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Rewind the line on the spool, if |
|
| Is the line jamming on the spool? |
| Yes |
| |
|
|
|
| symptoms still persist, change | ||
|
|
|
| |||
|
|
|
|
|
| spool and line. |
Contact Husqvarna UK Ltd. Customer Service
Telephone : 0870 609 1901
Environmental Information
•Awareness of the environment must be considered when disposing of
•If necessary, contact your local authority for disposal information.
The symbol on the product or on its packaging indi- cates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and elec- tronic equipment.
By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this prod- uct.
For more detailed information about recycling of this product, please contact your local council office, your household waste disposal service or the shop where you purchased the product.
Guarantee & Guarantee Policy
If any part is found to be defective due to faulty manufacture within the guarantee period, Husqvarna UK Ltd., through its Au- thorised Service Repairers will effect the repair or replacement to the customer free of charge providing:
(a)The fault is reported directly to the Authorised Repairer.
(b)Proof of purchase is provided.
(c)The fault is not caused by misuse, neglect or faulty adjust- ment by the user.
(d)The failure has not occurred through fair wear and tear.
(e)The machine has not been serviced or repaired, taken apart or tampered with by any person not authorised by Husqvarna UK Ltd.
(f)The machine has not been used for hire.
(g)The machine is owned by the original purchaser.
(h)The machine has not been used commercially.
*This guarantee is additional to, and in no way diminishes the
customers statutory rights.
Failures due to the following are not covered, therefore it is impor- tant that you read the instructions contained in this Operator's Man- ual and understand how to operate and maintain your machine:
Failures not covered by guarantee
*Replacing Nylon Line.
*Failures as a result of not reporting an initial fault.
*Failures as a result of sudden impact.
*Failures as a result of not using the product in accordance with the instructions and recommendations contained in this Operator's Manual.
*Machines used for hire are not covered by this guarantee.
*The following items listed are considered as wearing parts and their life is dependent on regular maintenance and are, therefore not normally subject to a valid warranty claim: Nylon Line, Spool and Line, Electric Mains Cable
*Caution!
Husqvarna UK Ltd. does not accept liability under the war- ranty for defects caused in whole or part, directly or indirectly by the fitting of replacement parts or additional parts that are not either manufactured or approved by Husqvarna UK Ltd., or by the machine having been modified in any way.