STANDARDS: This edger attachment is Listed by Underwriter’s Laboratories, Inc., in ac- cordance with UL Standard 1602,
31cc Powerhead (with trimmer attachment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . PP036 31cc Powerhead (with trimmer attachment) . . . . . . . . . . . . . . . . . . . . . . . . . . . . PP136
WARNING: If received assembled, repeat all steps to ensure your unit is properly assembled and all fasteners are secure.
Examine parts for damage. Do not use dam- aged parts.
NOTE: If you need assistance or find parts missing or damaged, call
TOOLS REQUIRED
SHex wrench (provided)
HANDLEBAR ASSEMBLY
DANGER: RISK OF CUT. To avoid serious injury, the barrier portion of the han- dlebar must be installed as shown on the up- per shaft of the powerheadto provide a barrier betweenoperator and the spinning blade. At- tach shaft clamp above arrow on safety warn- ing decal on the upper shaft (powerhead end of unit). Ensure handlebar is positioned on handlebar clamp between the arrows on the handlebar decal.
NOTE: The shaft clamp base has four spacer tabs attached. These tabs are pro- vided to adapt this attachment for use with powerheads that have a 1∀ diameter upper shaft (the shaft clamp will not tighten down se- curely on the 1∀ diameter upper shaft without using these spacer tabs). The tabs must be broken off completely before use and placed over the screw holes on the clamp base. These tabs are not needed for powerheads with a 7/8∀ upper shaft.
HANDLEBAR CLAMP BASE
Spacer Tabs
1.Place the shaft clamp over the upper shaft above the arrow on the safety decal.
2.Position the clamp base under the upper shaft and align the shaft clamp and clamp base screw holes (use spacer tabs be- tween shaft clamp and clamp base if nec- essary to secure clamp, i.e. for 1∀ diame- ter upper shaft).
Handlebar
POWERHEAD
END
Handlebar Clamp between arrows on handlebar decal
Clamp |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Clamp | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Base | |||
Knob |
|
|
|
|
|
| ||||||||||||||
|
|
|
|
|
| |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
Shaft | Screws | |||||||||||||||||||
Clamp |
|
|
|
|
|
|
|
|
|
|
| |||||||||
|
|
|
|
|
| Arrow on |
|
|
| |||||||||||
|
|
|
|
|
| Safety Decal |
|
|
| |||||||||||
ATTACHMENT |
|
|
| |||||||||||||||||
END |
|
|
| |||||||||||||||||
3.Insert the four screws into the screw holes.
4.Secure shaft clamp by tightening screws with the hex wrench.
5.Position the handlebar as shown, ensur- ing the handlebar is positioned on the han- dlebar clamp between the arrows on the handlebar decal.
6.Retighten handlebar by turning clamp knob clockwise until handlebar is secure and stationary in clamp (clamp knob can- not be overtightened).
Spacer Tabs positioned for use on 1∀ diameter upper shaft
5