Poulan 545154718, P3500 Stop Switch, Primer Bulb, Choke, Edge Guide, Fuel Requirements

Page 6

STOP SWITCH

The STOP switch is used to stop the engine. To stop the engine, push and hold the switch in the STOP position until the engine stops.

PRIMER BULB

The PRIMER BULB removes air from the car- buretor and fuel lines and fills them with fuel. This allows you to start the engine with fewer pulls on the starter rope. Activate the primer bulb by pressing it and allowing it to return to its original form.

CHOKE

The CHOKE helps to supply fuel to the engine to aid in cold starting. Activate the choke by moving the choke lever to the FULL CHOKE position. After the engine attempts to start, move the choke lever to the HALF CHOKE position. Once engine has started, move the choke lever to the RUN position.

EDGE GUIDE

The EDGE GUIDE protects the unit from con- tacting the ground during edging.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel information in the safety rules before you begin. If you do not understand the safety rules, do not attempt to fuel your unit. Call 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/WEED EATER brand synthetic oil is recommended. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by mixing 3.2 fluid ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. DO NOT USE automotive oil or marine oil. These oils will cause engine damage. When mixing fuel, follow

instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.

CAUTION: Never use straight gasoline in your unit. This will cause permanent engine damage and void the limited warranty.

FUEL REQUIREMENTS

This engine requires the use of minimum 87 octane [R+M]/2 clean gasoline.

IMPORTANT

Use of alcohol blended fuels (called gasohol or using ethanol or methanol) can cause major en- gine performance and durability problems.

WARNING: Alternative fuels (not gas- oline) such as E--15 (15% alcohol), E--20 (20% alcohol), E--85 (85% alcohol) are NOT classified as gasoline and are NOT approved for use in 2--stroke gasoline engines. Use of alternative fuels will cause problems such as: improper clutch engagements, overheating, vapor lock, power loss, lubrication deficiency, deterioration

of fuel lines, gaskets and internal carburetor components, etc. Alternative fuels cause high moisture absorption into the fuel/oil mixture leading to oil and fuel separation.

HELPFUL TIP

If your engine switch reads “push to stop”, it is always in the ON position.

HOW TO STOP YOUR UNIT

STo stop the engine, push and hold the STOP switch in the STOP position until the engine stops.

SIf engine does not stop, move choke to the FULL CHOKE position.

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any contact with the muffler. A hot muffler can cause serious burns.

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

NOTE: Make sure approximately 3 - 4 inches (8 - 10 cm) of line is extended from the cutting head before starting unit. This will allow the line to advance properly once the unit starts.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to the FULL CHOKE position.

4.Squeeze the throttle trigger fully and hold through all remaining steps.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Safety Rules Operator SafetyCutting Safety Unit / Maintenance SafetyFuel Safety Transporting and StorageOperation AssemblyAdjusting the Assist Handle Attaching ShieldHOW to Start Your Unit Stop SwitchHOW to Stop Your Unit Primer BulbOperating Position Starting a Warm EngineStarting a Flooded Engine Twist and EdgeTip of the Line Trimmer Line AdvanceCutting Methods Does The Cutting Work AreaMaintenance Installing Spool with Line Service and AdjustmentsLine Replacement Carburetor Idle Speed AdjustmentEngine Seasonal StorageFuel System OtherTroubleshooting Table Cause Remedy Limited Warranty Canada, contactReplacement and Repair of Emis

P3500, 545154718 specifications

The Poulan 545154718, P3500 is a powerful and versatile chainsaw designed for both residential and professional use. This model is well-known for its reliability and efficiency, making it a popular choice among homeowners, landscapers, and tree care professionals alike.

One of the standout features of the P3500 is its robust 50cc engine. This engine delivers ample power to tackle a wide range of cutting tasks, from trimming branches to felling medium-sized trees. The design of the engine not only ensures high performance but also offers easy starting capabilities, reducing the hassle for the user, especially in colder conditions or after extended periods of inactivity.

In terms of cutting performance, the Poulan P3500 is equipped with a 20-inch bar and chain, providing an ideal balance between cutting capacity and control. This length allows the user to efficiently cut through thicker logs while maintaining precision for smaller cuts. The chain itself is designed for durability, ensuring that it remains sharp and effective over time, which contributes to a smoother cutting experience.

The overall ergonomics of the design make the P3500 user-friendly. It features a lightweight construction, which helps reduce operator fatigue during extended use. The innovative handle design provides a comfortable grip, enhancing control and stability during cutting operations. Additionally, the chainsaw is equipped with anti-vibration technology, which further minimizes fatigue and allows for longer, more comfortable use.

Safety is a crucial aspect of any chainsaw, and the Poulan P3500 does not disappoint. It includes several safety features such as a chain brake and a throttle lock-out, ensuring that the user can operate the tool safely. The accessible air filter and fuel tank make maintenance easy, allowing users to keep their chainsaw in optimal condition with minimal effort.

Furthermore, the Poulan P3500 is designed with easy-to-use adjustments for chain tensioning, ensuring that the chain can be tightened or loosened without the need for additional tools. This feature enhances the convenience of the chainsaw, making it simpler for users to perform routine maintenance.

In conclusion, the Poulan 545154718, P3500 is a well-rounded chainsaw that delivers power, comfort, and safety in one package. With its features tailored for both novice and experienced users, it stands out as a reliable tool for anyone looking to manage their cutting tasks effectively. Whether you are pruning trees or tackling larger landscaping projects, the P3500 is engineered to meet your needs with performance and efficiency.
Top Page Image Contents