Poulan 545186843 Operating Instructions for USE with Weed Blade, Trimming, Scalping Sweeping

Page 13

SFor trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially:

S During light duty cutting.

S Near objects around which the line can wrap such as small posts, trees or fence wire.

SFor mowing or sweeping, use full throttle for a good clean job.

TRIMMING -- Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.

Trimming

3 inches (8 cm) above ground

SCALPING -- The scalping technique removes unwanted vegetation down to the ground. Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique in- creases line wear.

Scalping

Sweeping

OPERATING INSTRUCTIONS FOR USE WITH WEED BLADE

SBlade Thrust is a reaction that only occurs when using a bladed unit. This reaction can cause serious injury such as amputation. Carefully study this section. It is important that you understand what causes blade thrust, how you can reduce the chance of its occurring, and how you can remain in control

of unit if blade thrust occurs.

SWHAT CAUSES BLADE THRUST --Blade Thrust can occur when the spinning blade contacts an object that it does not cut. This contact causes the blade to stop for an instant and then suddenly move or “thrust” away from the object that was hit. The “thrusting” reaction can be violent enough to cause the operator to be propelled in any direction and lose control of the unit. The uncontrolled unit can cause serious injury if the blade contacts

the operator or others.

S WHEN BLADE THRUST OCCURS --Blade Thrust can occur without warning if

the blade snags, stalls, or binds. This is more likely to occur in areas where it is difficult to see the material being cut. By using the unit properly, the occurrence of blade thrust will be reduced and the operator will be less likely to lose control.

MOWING -- Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool.

Mowing

SWEEPING -- The fanning action of the rotat- ing line can be used to blow away loose debris from an area. Keep the line parallel to and above the area surface and swing the tool from side to side.

SCut only grass, weeds, and woody brush up to 1/2 inch (1 cm) in diameter with the weed blade. Do not let the blade contact material

it cannot cut such as stumps, rocks, fences, metal, etc., or clusters of hard, woody brush having a diameter greater than 1/2 inch (1 cm).

SKeep the blade sharp. A dull blade is more

likely to snag and thrust.

S Cut only at full throttle. The blade will have maximum cutting power and is less likely to bind or stall.

S“Feed” the blade deliberately and not too

rapidly. The blade can thrust away if it is fed too rapidly.

SCut only from your left to your right. Cutting on right side of the shield will throw debris away

from the operator.

SUse the shoulder strap and keep a firm grip on the unit with both hands. A properly

13

Image 13
Contents English Español Français Manual de Instrucciones Manuel d’InstructionsIdentification of Safety Symbols Table of ContentsHazard zone for thrown objects Operator Safety Safety RulesPowerhead model Attachments Type Part. no Optional AttachmentsFuel Safety UNIT/MAINTENANCE SafetyCutting Safety Transporting and StorageCarton Contents AssemblyInstalling Brushcutter Attachment Tools RequiredConfiguring Your Unit Assembly of Shoulder StrapAssembly Information Trimmer Head To Relocate Shoulder Strap ClampAttaching the Plastic Shield and Trimmer Head Assembly Information Weed BladeWeed Blade Attaching the Metal Shield Installation of the Metal BladeOperation HOW to Start Your Unit HOW to Stop Your UnitStarting a Warm Engine Starting a Flooded EngineOperating Position Installing Optional ATTACH- MentsOperating Instructions for USE with Trimmer Head Cutting MethodsTrimming Operating Instructions for USE with Weed BladeScalping Sweeping MowingEdger Safety Additional Safety RulesBLOWER/VACUUM Safety Recommended Cutting PositionHedge Trimmer Safety Cultivator SafetyPole Pruner Safety Break glass, or cause other damageOr when walking from one cutting location to another Snow Thrower SafetyKnow how to stop quickly Maintenance Blade Replacement Service and AdjustmentsCarburetor Idle Speed Adjustment Replacing the LineSeasonal Storage StorageFuel System EngineTroubleshooting Table Cause Remedy Canada, contact Limited WarrantyPoulan PRO Ligations The U.S. EnvironmentalNANCE, Replacement and Repair