Poulan 545186845 HOW to Stop Your Unit, HOW to Start Your Unit, Starting a Flooded Engine

Page 11

clutch engagements, overheating, vapor lock, power loss, lubrication deficiency, deterioration of fuel lines, gaskets and internal carburetor components, etc. Alternative fuels cause high moisture absorption into the fuel/oil mixture leading to oil and fuel separation.

HOW TO STOP YOUR UNIT

SRelease the throttle trigger.

S Push and release the engine ON/STOP switch. The switch will automatically return to the ON position. Wait 5 seconds before at- tempting to restart unit to allow switch to reset.

ON/STOP Switch

HOW TO START YOUR UNIT

WARNING: Avoid any contact with the muffler. A hot muffler can cause serious burns.

Starting Position

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

NOTE: DO NOT squeeze the throttle trigger until the engine has started and runs.

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move the start lever to the START position.

Primer Bulb

Starter Handle

NOTE: Normally, the warm starting procedure can be used within 5 -- 10 minutes after the unit is turned STOP. If the unit sits for more than 10 minutes without being run, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit.

STARTING A FLOODED ENGINE

Move the start lever to the RUN position and fully squeeze throttle trigger. Pull the starter handle repeatedly while squeezing throttle trigger until engine starts and runs. This could require pulling the starter handle many times, depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLE- SHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which enables optional attachments to be installed. The optional attachments are:

MODEL:

Edger . . . . . . . . . . . . . . . . . . . . . . PP1000E Cultivator . . . . . . . . . . . . . . . . . . . PP2000T Blower . . . . . . . . . . . . . . . . . . . . . PP3000B Brushcutter . . . . . . . . . . . . . . . . . PP4000C Pruner . . . . . . . . . . . . . . . . . . . . . PP5000P Pruner . . . . . . . . . . . . . . . . . . . . . PP5500P

WARNING: Always stop unit and dis- connect spark plug before removing or instal- ling attachments.

REMOVING TRIMMER ATTACH- MENT (OR OTHER OPTIONAL AT- TACHMENTS)

CAUTION: When removing or installing at- tachments, place the unit on a flat surface for stability.

1.Loosen the coupler by turning the knob counterclockwise.

Upper shaft

Coupler

LOOSEN

Attachment

ThrottleMuffler

Trigger Start

Lever

4.Pull starter rope handle sharply until en- gine starts and runs.

5.Allow unit to run for 10--15 seconds, then fully squeeze the throttle trigger to disen- gage the starting system.

STARTING A WARM ENGINE

Pull starter rope sharply until engine starts and runs.

TIGHTEN Knob

2.Press and hold the locking/release button. Locking/release

button

Coupler

Upper shaft

Attachment

 

3.While securely holding the engine and upper shaft, pull the attachment straight out of the coupler.

INSTALLING OPTIONAL ATTACH- MENTS

1.Remove the shaft cap from the attach- ment (if present).

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Table of ContentsIdentification of Safety Symbols Optional Attachments Safety RulesOperator Safety Transporting and Storage Unit / Maintenance SafetyFuel Safety Line Trimmer SafetyHandlebar Edger SafetyBLOWER/VACUUM Safety Brushcutter SafetyPole Pruner Safety Cultivator SafetyHedge Trimmer Safety Head Snow Thrower SafetyHigh speed causing injury Card blades that are bent, warped, cracked or brokenAttaching Shield AssemblyInstalling Trimmer ATTACH- Ment Adjusting the Assist HandleOperation Starting a Flooded Engine HOW to Stop Your UnitHOW to Start Your Unit Installing Optional ATTACH- MentsLocking/Release Button in Primary Hole Operating PositionTrimmer Line Advance Cutting MethodsCheck for Loose Fasteners and Parts MaintenanceInspect and Clean Unit and Labels Clean AIR FilterReplacing the Line Service and AdjustmentsMuffler and Spark ARREST- ING Screen Replace Spark PlugSlot Fuel System Carburetor Idle Speed AdjustmentReplacing the Trimmer Head Seasonal StorageTrouble Cause Remedy Troubleshooting TableEngine OtherLigations The U.S. Environmental Limited WarrantyCanada, contact Poulan PRONANCE, Replacement and Repair

545186845 specifications

The Poulan 545186845 is a robust and versatile chainsaw that caters to both novice and experienced users, making it an excellent choice for homeowners and professionals alike. Known for its reliability and power, this chainsaw is ideal for a variety of cutting tasks, including tree felling, limb pruning, and firewood preparation.

One of the standout features of the Poulan 545186845 is its powerful engine. It is equipped with a 50cc, 2-stroke engine that delivers ample power for demanding cutting applications, allowing users to tackle larger logs and tough wood with ease. The engine is designed to provide an excellent power-to-weight ratio, ensuring that the chainsaw remains manageable even during extended use.

The chainsaw utilizes a specially designed air filtration system that enhances its performance and prolongs engine life. This system minimizes the amount of dust and debris that enters the engine, resulting in less maintenance and longer periods between filter cleaning. This technology not only extends the lifespan of the unit but also ensures consistent performance during operation.

Another key characteristic is its ease of use. The Poulan 545186845 features an automatic oiling system that maintains proper lubrication to the bar and chain, reducing friction and wear during cutting. Additionally, the chainsaw has a tool-less chain tensioning system, allowing users to quickly adjust the chain tension without the need for any additional tools. This combination of features makes it convenient for users to perform maintenance and adjustments in the field.

Safety is paramount in the design of the Poulan 545186845. It comes equipped with a chain brake that automatically engages in the event of kickback, providing an added layer of protection for the operator. The anti-vibration handle also enhances comfort during use, reducing user fatigue and improving control during prolonged tasks.

The Poulan 545186845 is designed for durability and reliability, with a robust construction that withstands the rigors of regular use. Its lightweight design further enhances its usability, allowing users to maneuver the chainsaw easily while ensuring that it does not become overly burdensome during cutting sessions.

In summary, the Poulan 545186845 is a powerful, versatile, and user-friendly chainsaw that incorporates advanced technology and features. With its strong engine, effective air filtration system, automatic oiling, and safety enhancements, it is a reliable tool for anyone looking to tackle outdoor cutting tasks effectively and efficiently. Whether you're a seasoned professional or a weekend warrior, this chainsaw is sure to meet your needs and exceed your expectations.
Top Page Image Contents