Poulan PP446ET BAR and Chain Lubrication, HOW to Stop Your Unit, HOW to Start Your Unit

Page 13

WARNING: Alternative fuels (not gas- oline) such as E--15 (15% alcohol), E--20 (20% alcohol), E--85 (85% alcohol) are NOT classified as gasoline and are NOT approved for use in 2--stroke gasoline engines. Use of alternative fuels will cause problems such as: improper clutch engagements, overheating, vapor lock, power loss, lubrication deficiency, deterioration of fuel lines, gaskets and internal carburetor components, etc. Alternative fuels cause high moisture absorption into the fuel/oil mixture leading to oil and fuel separation.

BAR AND CHAIN LUBRICATION

The bar and chain require lubrication. The chain oiler provides continuous lubrication to the chain and guide bar. Be sure to fill the bar oil tank when you fill the fuel tank (Capacity = 4.6 fl. oz.). Lack of oil will quickly ruin the bar and chain. Too little oil will cause overheating shown by smoke coming from the chain and/or discolor- ation of the bar. The oil output is automatically metered during operation. Always fill the bar oil tank when you fill the fuel tank.

Genuine Poulan or Poulan PRO bar and chain oil is recommended to protect your unit against excessive wear from heat and fric- tion. Poulan or Poulan PRO oil resists high temperature thinning. If Poulan or Poulan PRO bar and chain oil is not available, use a good grade SAE 30 oil.

S Never use waste oil for bar and chain lubrication.

S Always stop the engine before removing the oil cap.

HOW TO STOP YOUR UNIT

SRelease the throttle trigger.

S Push and release the engine ON/STOP switch. The switch will automatically return to the ON position. Wait 5 seconds before attempting to restart unit to allow switch to reset.

ON/STOP Switch

HOW TO START YOUR UNIT

WARNING: Make sure the chain will not make contact with any object while starting the engine. Never try to start the unit when the guide bar is in a cut. Avoid any contact with the muffler. A hot muffler can cause serious burns.

Starting Position

HELPFUL TIP

If your engine still does not start after following these instructions, please call 1-800-554-6723.

STARTING A COLD ENGINE

NOTE: DO NOT squeeze the throttle trigger until the engine has started and runs.

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move the start lever to the START posi- tion.

Starter Handle

Start

Lever

Primer Bulb

Muffler

4.Pull starter rope handle sharply until en- gine starts and runs.

5.Allow unit to run for 5 seconds, then fully squeeze the throttle trigger to disengage the starting system.

STARTING A WARM ENGINE

1.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until engine runs smoothly.

2.Pull starter rope sharply while squeezing

throttle trigger until engine runs. NOTE: Normally, the warm starting proce- dure can be used within 5--10 minutes after the unit is turned off. If the unit sits for more than 10 minutes without being ran, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the start lever in the RUN position. Fully squeeze throttle trigger. Pull the starter han- dle repeatedly while squeezing throttle trigger until engine starts and runs. This could re- quire pulling the starter handle many times, depending on how badly the unit is flooded. If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.

OPERATING THE COUPLER

This model is equipped with a coupler which enables optional attachments to be installed. The optional attachments are:

MODEL: Edger . . . . . . . . . . . . . . . . . . . . . . . PP1000E Cultivator . . . . . . . . . . . . . . . . . . . . PP2000T Blower . . . . . . . . . . . . . . . . . . . . . . PP3000B Brushcutter . . . . . . . . . . . . . . . . . . PP4000C

WARNING: Always stop unit and dis- connect spark plug before removing or instal- ling attachments.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Manual de Instrucciones Manuel d’Instructions Identification of Safety Symbols Hazard zone for thrown objects Identification of Safety Symbols Pruner Safety Safety RulesLine Trimmer Safety Plan AheadHandle Fuel with Caution Maintain Your Unit in Good Working OrderKickback Reduce the Chance KickbackMaintain Control Kickback Safety FeaturesFor Optional Attachments TipBLOWER/VACUUM Safety Edger SafetyBrushcutter Safety Skid in contact with the groundHedge Trimmer Safety Cultivator SafetySnow Thrower Safety Away from the operatorTools Required AssemblyAdjusting the Assist Handle Shoulder Strap AssemblyTo Relocate Shoulder Strap Clamp Attaching Shield for Line Trimmer AttachmentOperation HOW to Start Your Unit HOW to Stop Your UnitBAR and Chain Lubrication Starting a Cold EngineInstalling Optional ATTACH- Ments Installing Attachment HangerLower Attachment Locking/Release Button CouplerPruning Technique Pruning Important PointsTrimmer Line Advance Will fallGrassy area Cutting MethodsWays are shown below Tip of the Line Does The Cutting Work AreaMaintenance Service and Adjustments Replacing the Line Chain AdjustmentReplacing the Trimmer Head Seasonal Storage Carburetor Idle Speed AdjustmentFuel System EngineEmpty fuel tank and refill with Troubleshooting Table Cause RemedySee Fueling Engine in Operation Canada, contact Limited WarrantyLigations The U.S. Environmental Repair or Replacement of Parts

PP446ET, 545177333 specifications

The Poulan 545177333 PP446ET is a cutting-edge chainsaw designed for both professional and home applications, offering efficiency and ease of use for a variety of cutting tasks. This model is particularly known for its robust design, powerful engine, and user-friendly features, making it a popular choice among landscapers, contractors, and DIY enthusiasts.

One of the standout features of the PP446ET is its powerful 46cc two-stroke engine. This engine provides ample power for tackling tough jobs, from trimming trees to cutting firewood. The engine is designed with fuel efficiency in mind, ensuring that users can complete their tasks without frequent refueling interruptions. Additionally, the engine is engineered for reduced emissions, aligning with modern environmental standards and making it a more eco-friendly option.

The Poulan PP446ET is equipped with a 18-inch bar, allowing for greater reach and enhanced cutting capacity. This length is ideal for a wide range of tasks, from light pruning to larger limb removal and even felling small trees. The chainsaw features a low-profile chain, which aids in smoother cutting and reduces kickback, making it safer for inexperienced users.

A key technological advancement in the PP446ET is its automatic oiling system. This system ensures consistent lubrication of the chain and bar, reducing wear and increasing the lifespan of the chainsaw. Moreover, the tool-free chain tensioning feature simplifies maintenance, allowing users to easily adjust the chain tension without the need for additional tools.

User comfort is also a priority in the design of the PP446ET. The chainsaw features an ergonomic handle, which provides a secure grip and reduces fatigue during prolonged usage. The anti-vibration technology incorporated into the design further enhances comfort, allowing users to work longer without discomfort.

Safety features are paramount in any chainsaw, and the PP446ET excels in this area. The chainsaw is equipped with a chain brake that stops the chain almost immediately in the event of a kickback, along with a safety throttle lock to prevent accidental starts.

Overall, the Poulan 545177333 PP446ET stands out as a reliable, powerful, and user-friendly chainsaw. Its combination of innovative technologies, user-centric design, and robust performance makes it an excellent choice for anyone looking to tackle their cutting tasks with efficiency and ease.
Top Page Image Contents