Poulan PP446E, 545137279 instruction manual Operation

Page 9

4.Insert two screws into the screw holes.

5.Secure shoulder strap clamp by tighten- ing screws with a hex wrench.

ADJUSTING THE ASSIST HANDLE

WARNING: When adjusting the as- sist handle, be sure it remains between the

coupler and the lower arrow (closest to coupler) on the safety label to ensure proper

balancing of unit. When adjusting the assist handle or handlebar during use of optional at- tachments, it must be repositioned between

the throttle trigger and the upper arrow (closest to engine) on the safety label.

1.Loosen wing nut on handle.

2.Rotate the handle on the shaft to an up- right position; retighten wing nut.

OPERATION

KNOW YOUR PRUNER

READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference.

Pruner

Assist Handle Coupler

ON/OFF Switch

Shaft

Attachment Hanger

Bar oil fill cap

Chain

Bar

Bar nut

 

ON/OFF SWITCH

The ON/OFF switch is located on the trigger handle and is used to stop the engine. Move the switch to the OFF position to stop the engine.

PRIMER BULB

The PRIMER BULB removes air from the car- buretor and fuel lines and fills them with fuel. This allows you to start the engine with fewer pulls on the starter rope. Activate the primer bulb by pressing it and allowing it to return to its original form.

START LEVER

The START LEVER helps to supply fuel to the engine to aid in starting. Activate the starting

Shoulder strap clamp

Starter handle Fuel mix fill cap

Primer bulb

Throttle trigger

Start lever

Muffler

 

system by moving the start lever to the START position. DO NOT squeeze the throttle trigger until the engine has started and runs. After the engine starts, allow the engine to warm--up 5 seconds, then fully squeeze the throttle trigger to deactivate the starting system.

COUPLER

The COUPLER enables optional attach- ments to be installed on the unit.

CHAIN TENSION

It is normal for a new chain to stretch during first 15 minutes of operation. You should check your chain tension frequently. See CHAIN TENSION in the SERVICE AND AD- JUSTMENTS section.

BEFORE STARTING ENGINE

WARNING: Be sure to read the fuel information in the safety rules before you be- gin. If you do not understand the safety rules, do not attempt to fuel your unit. Call 1-800-554-6723.

FUELING ENGINE

WARNING: Remove fuel cap slowly when refueling.

HELPFUL TIP

To obtain the correct oil mix ratio, pour 3.2 ounces of 2-cycle synthetic oil into one gallon of fresh gas.

This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/WEED EATER brand synthetic oil is

9

Image 9
Contents PP446E Identification of Symbols Safety RulesPlan Ahead Maintain Your Pruner in Good Working Order Operate Your Pruner SafelyHandle Fuel with Caution KickbackReduce the Chance Kickback Kickback Safety FeaturesMaintain Control TipLine Trimmer Safety Edger SafetyBLOWER/VACUUM Safety For Optional AttachmentsCultivator Safety Brushcutter SafetyProper air flow Curs, stop the engine and inspect the unit for damageSnow Thrower Safety Hedge Trimmer SafetyHead Essary before restarting unitInstalling Pruner ATTACH- Ment AssemblyShoulder Strap Assembly Tools RequiredOperation HOW to Start Your Unit HOW to Stop Your UnitBAR and Chain Lubrication Starting a Cold EngineInstalling Optional ATTACH- Ments Installing Attachment HangerOperating the Coupler Removing Pruner Attachment or Other Optional Attach MentsPruning Important Points Pruning TechniqueFoot Maintenance Service and Adjustments Carburetor Adjustment Chain AdjustmentIdle Speed Adjustment To Replace ChainFuel System Seasonal StorageEngine OtherLoad Adjustment Troubleshooting Table Cause RemedyCompression low Carbon build-up onLigations The U.S. Environmental Limited Warranty800--554--6723 Service