Poulan FL26 instruction manual Operating Position, Trimmer Line Advance, Cutting Methods

Page 6

OPERATING INSTRUCTIONS

It is recommended that the engine not be operated for longer than 1 minute at full throttle.

OPERATING POSITION

ALWAYS WEAR:

Eye protection

Long pants

Heavy shoes

Cut from your right to your left.

WARNING: Always wear eye protec- tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury.

Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool.

Always release the throttle trigger and allow the engine to return to idle speed when not cutting.

To stop engine:

SRelease the throttle trigger.

S Push and hold the STOP switch in the STOP position until the engine stops.

TRIMMER LINE ADVANCE

The trimmer line will advance approximately 2 inches (5 cm) each time the bottom of the trimmer head is tapped on the ground with the engine running at full throttle.

The most efficient line length is the maximum length allowed by the line limiter.Always keep the shield in place when the tool is being oper- ated.

To advance line:

SOperate the engine at full throttle.

SHold the trimmer head parallel to and above

the grassy area.

STap the bottom of the trimmer head lightly on the ground one time. Approximately 2 inches (5 cm) of line will be advanced with each tap.

Always tap the trimmer head on a grassy area. Tapping on surfaces such as concrete or asphalt can cause excessive wear to the trimmer head.

If the line is worn down to 2 inches (5 cm) or less, more than one tap will be required to ob- tain the most efficient line length.

WARNING: Use only 0.080(2 mm) diameter line. Other sizes of line will not ad- vance properly and will result in improper cut- ting head function or can cause serious injury. Do not use other materials such as wire, string, rope, etc. Wire can break off during cutting and become a dangerous missile that can cause serious injury.

CUTTING METHODS

WARNING: Use minimum speed and do not crowd the line when cutting around hard objects (rock, gravel, fence posts, etc.), which can damage the trimmer head, become entangled in the line, or be thrown causing a serious hazard.

SThe tip of the line does the cutting. You will achieve the best performance and mini- mum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below.

Tip of the Line

Line Crowded Into

Does The Cutting

Work Area

RightWrong

S The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences. To help avoid damage especially to delicate vegetation or trees with tender bark, shorten line to 4--5 inches (10--13 cm) and use at less than full throttle.

SFor trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially:

S During light duty cutting.

S Near objects around which the line can wrap such as small posts, trees or fence

wire.

SFor mowing or sweeping, use full throttle for a good clean job.

TRIMMING -- Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.

Trimming

3 inches (8 cm) above ground

SCALPING -- The scalping technique re- moves unwanted vegetationdown to the ground. Hold the bottom of the trimmer head about 3 inches (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear.

6

Image 6
Contents Manual de Instrucciones Manuel d’Instructions Unit / Maintenance Safety Safety RulesOperator Safety Fuel SafetyAdjusting the Handle AssemblyCutting Safety Transporting and StorageOperation Starting a Warm Engine HOW to Stop Your UnitHOW to Start Your Unit Starting a Flooded EngineOperating Position Trimmer Line AdvanceCutting Methods Maintenance Carburetor Adjustment Service and AdjustmentsLine Replacement Engine will not idle when the throttle is re- leasedEngine Seasonal StorageFuel System OtherTroubleshooting Table Cause Remedy Limited Warranty Ligations The U.S. EnvironmentalConsequential Damages Weed