HOW to Start Your Unit, Starting a Warm Engine

Engine Choke Lever

ON/STOP

Switch

FULL HALF OFF

HOW TO START YOUR UNIT

WARNING: The trimmer head will turn while starting the engine. Avoid any con- tact with the muffler. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

Starting Position

1.Set unit on a flat surface.

2.Slowly press the primer bulb 6 times.

3.Move choke lever to the FULL CHOKE position.

4.Squeeze the throttle trigger fully and hold through all remaining steps.

Starter Handle

Choke

Lever

Muffler

Primer Bulb

5.Pull starter rope handle sharply until engine sounds as if it is trying to start, but do not pull rope more than 6 times.

6.As soon as engine sounds as if it is trying to start, move choke lever to HALF CHOKE position.

7.Pull starter rope sharply until engine runs, but no more than 6 pulls.

NOTE: If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the start- er rope until the engine runs, but no more than 6 pulls. If the engine still doesn’t start, it is probably flooded. Proceed to

STARTING A FLOODED ENGINE.

8.Once the engine starts, allow it to run 10 seconds, then move the choke lever to the OFF CHOKE position. Allow the unit

to run for 30 more seconds at OFF CHOKE before releasing the throttle trig- ger.

NOTE: If engine dies with the choke le- ver in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.

STARTING A WARM ENGINE

1.Move the choke lever to the HALF CHOKE position.

2.Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the engine runs smoothly.

3.Pull starter rope sharply until engine runs, but no more than 5 pulls.

4.Allow engine to run 15 seconds, then move the choke lever to the OFF CHOKE position.

NOTE: If engine has not started, pull start- er rope 5 more pulls. If engine still does not run, it is probably flooded.

STARTING A FLOODED ENGINE

Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex- cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.

If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554--6723.

OPERATING POSITION

Cut from your left to your right.

WARNING: Always wear eye protec- tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury.

Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool.

Always release the throttle trigger and allow the engine to return to idle speed when not cutting.

To stop engine:

S Release the throttle trigger.

PL500 specifications

The Poulan PL500 is a versatile and efficient piece of outdoor equipment designed for homeowners and landscaping professionals alike. A chainsaw that emphasizes reliability and ease of use, the PL500 stands out in its category with a blend of powerful performance and practical features.

One of the main features of the Poulan PL500 is its robust engine. Powered by a 50cc two-stroke engine, it delivers impressive cutting power, allowing users to tackle a variety of tasks, from trimming small branches to felling larger trees. The engine is designed for easy starting, thanks to its advanced starting technology that minimizes pull effort while maximizing reliability.

The PL500 is equipped with a 20-inch bar and a low-profile chain. This combination not only enhances cutting efficiency but also reduces kickback, making it safer for users. The low-profile chain is designed for smoother operation and can easily slice through wood with minimal resistance, allowing for quicker work on any project.

Another standout characteristic of the Poulan PL500 is its ergonomic design. The chainsaw features a comfortable grip handle that minimizes vibration, reducing fatigue during prolonged use. The rear handle is designed for secure handling, enabling users to maneuver the chainsaw with ease. A front hand guard adds an extra layer of safety, protecting the user from potential debris during operation.

In terms of maintenance, the PL500 simplifies the user experience. It is equipped with a built-in automatic oiler that ensures the chain remains properly lubricated during use, prolonging the life of both the bar and the chain. Additionally, the air filter is easily accessible, allowing for quick and hassle-free cleaning or replacement, which is crucial for maintaining optimal engine performance.

The Poulan PL500 also focuses on environmental considerations, incorporating technologies to minimize emissions and fuel consumption. This eco-friendly approach not only helps users comply with environmental regulations but also contributes to a cleaner outdoor environment for everyone.

In summary, the Poulan PL500 chainsaw is an impressive tool equipped with a powerful engine, a long bar for versatile cutting capability, ergonomic features for user comfort, and maintenance-friendly technologies. Whether you're a seasoned professional or a first-time user, the PL500 delivers on both performance and safety, making it a valuable addition to any outdoor toolkit.