Poulan PL500 Trimmer Line Advance, Cutting Methods, Push and release the engine ON/STOP switch

Page 6

S Push and release the engine ON/STOP switch.

TRIMMER LINE ADVANCE

The trimmer line will advance approximately 2 in. (5 cm) each time the bottom of the trimmer head is tapped on the ground with the engine running at full throttle.

The most efficient line length is the maximum length allowed by the line limiter.Always keep the shield in place when the tool is being oper- ated.

To advance line:

SOperate the engine at full throttle.

SHold the trimmer head parallel to and above

the grassy area.

STap the bottom of the trimmer head lightly on the ground one time. Approximately 2 in. (5 cm) of line will be advanced with each

tap.

Always tap the trimmer head on a grassy area. Tapping on surfaces such as concrete or asphalt can cause excessive wear to the trimmer head.

If the line is worn down to 2 inches (5 cm) or less, more than one tap will be required to ob- tain the most efficient line length.

WARNING: Use only 0.080! (2 mm) diameter line. Other sizes of line will not ad- vance properly and can cause serious injury. Do not use other materials such as wire, string, rope, etc. Wire can break off during cutting and become a dangerous missile that can cause serious injury.

CUTTING METHODS

WARNING: Use minimum speed and do not crowd the line when cutting around hard objects (rock, gravel, fence posts, etc.), which can damage the trimmer head, become entangled in the line, or be thrown causing a serious hazard.

SThe tip of the line does the cutting. You will achieve the best performance and minimum line wear by not crowding the line into the cutting area. The right and wrong ways are shown below.

S The line will easily remove grass and weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences.

SFor trimming or scalping, use less than full throttle to increase line life and decrease head wear, especially:

SDuring light duty cutting.

S Near objects around which the line can wrap such as small posts, trees or fence wire.

SFor mowing or sweeping, use full throttle for a good clean job.

TRIMMING -- Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.

Trimming

SCALPING -- The scalping technique re- moves unwanted vegetation. Hold the bottom of the trimmer head about 3 in. (8 cm) above the ground and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique increases line wear.

MOWING -- Your trimmer is ideal for mowing in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool.

6

Image 6
Contents Manual de Instrucciones Manuel d’Instructions Fuel Safety Operator SafetyUnit / Maintenance Safety Eye Protection Hazard ZoneTransporting and Storage Cutting SafetyAdjusting the Handle Attaching ShieldKnow Your Trimmer ON/STOP SwitchHOW to Stop Your Unit Primer BulbStarting a Flooded Engine HOW to Start Your UnitStarting a Warm Engine Operating PositionPush and release the engine ON/STOP switch Trimmer Line AdvanceCutting Methods Check for Loose Clean AIR FilterInspect and Clean Unit and DE Fasteners and PartsReplacing the Cutting Head Carburetor AdjustmentReplacing the Line Seasonal StorageTroubleshooting Table Other Trouble Cause RemedyAgency and POULAN/WEED EATER, Divi

PL500 specifications

The Poulan PL500 is a versatile and efficient piece of outdoor equipment designed for homeowners and landscaping professionals alike. A chainsaw that emphasizes reliability and ease of use, the PL500 stands out in its category with a blend of powerful performance and practical features.

One of the main features of the Poulan PL500 is its robust engine. Powered by a 50cc two-stroke engine, it delivers impressive cutting power, allowing users to tackle a variety of tasks, from trimming small branches to felling larger trees. The engine is designed for easy starting, thanks to its advanced starting technology that minimizes pull effort while maximizing reliability.

The PL500 is equipped with a 20-inch bar and a low-profile chain. This combination not only enhances cutting efficiency but also reduces kickback, making it safer for users. The low-profile chain is designed for smoother operation and can easily slice through wood with minimal resistance, allowing for quicker work on any project.

Another standout characteristic of the Poulan PL500 is its ergonomic design. The chainsaw features a comfortable grip handle that minimizes vibration, reducing fatigue during prolonged use. The rear handle is designed for secure handling, enabling users to maneuver the chainsaw with ease. A front hand guard adds an extra layer of safety, protecting the user from potential debris during operation.

In terms of maintenance, the PL500 simplifies the user experience. It is equipped with a built-in automatic oiler that ensures the chain remains properly lubricated during use, prolonging the life of both the bar and the chain. Additionally, the air filter is easily accessible, allowing for quick and hassle-free cleaning or replacement, which is crucial for maintaining optimal engine performance.

The Poulan PL500 also focuses on environmental considerations, incorporating technologies to minimize emissions and fuel consumption. This eco-friendly approach not only helps users comply with environmental regulations but also contributes to a cleaner outdoor environment for everyone.

In summary, the Poulan PL500 chainsaw is an impressive tool equipped with a powerful engine, a long bar for versatile cutting capability, ergonomic features for user comfort, and maintenance-friendly technologies. Whether you're a seasoned professional or a first-time user, the PL500 delivers on both performance and safety, making it a valuable addition to any outdoor toolkit.