Poulan 25 HHT Carburetor Adjustment, Blade Adjustment, Underside of Blade, TOP Side Blade

Page 7

As your unit is used, carbon deposits build up on the muffler and spark arresting screen. For normal homeowner use, however, the muffler and spark arresting screen will not re- quire any service. After 50 hours of use, we recommend that your muffler be serviced or replaced by your authorized service dealer.

CARBURETOR ADJUSTMENT

WARNING: Keep others away when making idle speed adjustments. The blade will be moving during most of this procedure. Wear your protective equipment and observe all safety precautions. When making adjust- ments, use a screwdriver short enough to keep your hands behind the handguard and away from the blade. After making adjust- ments, the blade must not move at idle speed. The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions:

SEngine will not idle when the throttle is re- leased.

SThe blade moves at idle.

Keep others away when making idle speed adjustments. Make adjustments with the unit resting on a level surface free of debris that can be caught in the hedge trimmer blade. Serious injury to the operator and others can occur if the carburetor is not properly adjusted. Keep all parts of your body away from the blade and muffler.

Idle Speed Adjustment

Allow engine to idle. Adjust speed until engine runs without blade moving (idle too fast) or en- gine stalling (idle speed too slow).

S Turn idle speed screw clockwise to in- crease enginespeed if engine stalls or dies.

STurn idle speed screw counterclockwise to decrease engine speed if the blade moves at idle.

WARNING: Recheck the idle speed after each adjustment. The blade must not move at idle speed to avoid serious injury to the operator or others.

Idle Speed Screw

If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1--800--554--6723.

BLADE ADJUSTMENT

The clearance between the cutting blades must be adjusted periodically to maintain opti- mal performance and sharp cutting.

Nut

Blade guide

Blades

Flat

 

 

 

 

 

 

 

 

 

 

Cupped

Washer

 

 

 

 

Bolt

Washer

Blade

 

 

 

 

 

 

 

 

 

 

 

Nuts

 

 

 

 

 

 

 

 

 

 

guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1.Using a wrench, loosen each nut on the top side of the blade guide.

Nut TOP SIDE OF BLADE

Wrench

2.Tighten each bolt from underside of blade with a wrench.

UNDERSIDE OF BLADE

Bolt

3. Loosen each bolt 1/2 turn.

1/2 turn

UNDERSIDE OF BLADE

 

Bolt

4.While holding each bolt in place with a wrench, retighten the nuts.

TOP SIDE

OF BLADE

-- 7 --

Page 6 Page 8
Image 7
Page 6 Page 8
Contents 12/1/03 530163900Operate Your Unit Safely Know Your UnitPlan Ahead Handle Fuel with CautionAssembly Throttle Trigger ON/OFF Switch Primer BulbKnow Your Hedge Trimmer ChokeStarting Your Engine Important PointsOperating Position Stopping Your EngineStarting a Flooded Engine Inspect and Clean Unit and LabelsClean AIR Filter Starting a Warm EngineTOP Side Blade Carburetor AdjustmentBlade Adjustment Underside of BladeSeasonal Storage Replace Fuel FilterReplace Spark Plug Fuel SystemOther Need Service PARTS?Troubleshooting Table Cause Remedy EngineLigations The U.S. Environmental Policy of Electrolux Home PROElectrolux Home PRODUCTS, INC Elec Ranty. Emission Control WarrantyHome Products INC Sion Related Parts Any Electro

25 HHT specifications

The Poulan 25 HHT is a versatile and powerful tool designed for landscaping and yard maintenance. Known for its reliability and efficiency, this model has become a favorite among both professionals and homeowners looking to keep their outdoor spaces tidy and well-groomed.

One of the standout features of the Poulan 25 HHT is its robust 25cc, 2-cycle engine. This powerful engine not only provides the necessary torque to handle tough weeds and dense brush but is also designed for easy starting, thanks to Poulan's Easy Start technology. This feature minimizes the effort required to start the engine, allowing users to get to work without the usual frustration associated with pull-start motors.

In terms of cutting capabilities, the Poulan 25 HHT is equipped with a bump feed trimmer head, which allows for quick and easy line advancement. This means that users can keep mowing without interruption, making the chore of yard work much more efficient. The double line feature provides wider cuts, ensuring faster trimming and a cleaner look in less time. Additionally, the trimmer head is designed for easy line replacement, further enhancing user convenience.

The design of the Poulan 25 HHT takes ergonomics into account, featuring a lightweight and balanced structure that reduces user fatigue during extended use. The adjustable handle enables users to customize their grip, enhancing comfort and control while trimming.

Another significant characteristic of this model is its versatility. The Poulan 25 HHT is not just a string trimmer; it can be attached to various accessories that transform it into a multi-tool. This includes capabilities for edging, cultivating, and even brush cutting. Such versatility makes it a cost-effective solution for homeowners who need multiple tools for their landscaping needs.

Safety is also a priority with the Poulan 25 HHT. It features a guard that protects the user while allowing for efficient discharge of cut grass and debris. The overall build quality ensures durability, allowing the unit to withstand tough conditions and extensive use.

In conclusion, the Poulan 25 HHT stands out as an excellent choice for anyone in need of a reliable, powerful, and versatile trimmer. Its combination of a strong 25cc engine, user-friendly features, and adaptability make it a valuable addition to any garden maintenance arsenal, helping users achieve a beautifully manicured landscape with ease.
Top Page Image Contents