Homelite UT20005 manual String Replacement, Cleaning the Exhaust Port and Muffler Spark Arrestor

Page 17

MAINTENANCE

STRING REPLACEMENT

See Figures 16 - 19.

nStop the engine, disconnect the spark plug wire. Hold the string head and unscrew the spool retainer.

To remove the spool retainer:

Turn the spool retainer counterclockwise for Trimlite and Trim n’ Edge.

Turn the spool retainer clockwise for Easy Reach.

nRemove the spool from the string head.

NOTE: Keep the spring attached to the spool. Remove any old string remaining on the spool.

nCut two pieces of string, each being approximately 9 ft. (2.7 m) long. Use only .080 in. (2.0 mm) diameter mono- filament string.

nInsert the first string into the anchor hole in the upper part of the spool. Wind the first string around the upper part of the spool counterclockwise, as shown by the arrows on the spool. Place string in the slot on upper spool flange, leaving about 6 in. (152 mm) extended beyond the slot. Do not overfill. After winding the string, there should be at least 1/4 in. (6 mm) between the wound string and the outside edge of the spool.

nRepeat above step with second string, using the bottom part of spool. Do not overfill.

nReplace the spool and the spool retainer. Refer to “Spool Replacement” earlier in this manual.

CLEANING THE EXHAUST PORT AND MUFFLER

NOTE: Depending on the type of fuel used, the type and amount of oil used, and/or your operating conditions, the exhaust port, muffler, and/or spark arrestor screen may be- come blocked with carbon deposits. If you notice a power loss with your gas powered tool, you may need to remove these deposits to restore performance. We highly recommended that only qualified service technicians perform this service.

SPARK ARRESTOR

The spark arrestor must be cleaned or replaced every 25 hours or yearly to ensure proper performance of your product. Spark arrestors may be in different locations depending on the model purchased. Please contact your nearest service dealer for the location of the spark arrestor for your model.

SPRING

FIRST STRING

FIRST STRING

SLOT

SPOOL

ARROWS ON

SPOOL

ANCHOR HOLE

Fig. 16

Fig. 17

SECOND

STRING

Fig. 18

SLOT

Page 17

ARROWS ON

SPOOL

Fig. 19

Image 17
Contents Operators Manual Introduction Table of ContentsRead ALL Instructions General Safety RulesSpecific Safety Rules for Trimmer USE Specific Safety RulesSymbol Name Explanation SymbolsSymbol Signal Meaning ServiceUnpacking SpecificationsInstructions Packing ListTrimlite model UT20004, UT20005 FeaturesTrim ‘n Edge model UT20024, UT20025 See Figure AssemblyFront Handle See Figures 5 Straight Shaft Grass Deflector Easy ReachOperating the Trimmer OperationFueling and Refueling the Trimmer Advancing the String Trimlite and Trim ‘N EdgeAdvancing the String Manually CUT OFF BladeSee Figures 10 Edger Guide Operation Trim ‘N Edge onlySee Starting and StoppingTo Start a Cold Engine To Stop the EngineSpool Replacement MaintenanceNEW Prewound Spool See Figures 14See Figures 16 String ReplacementCleaning the Exhaust Port and Muffler Spark Arrestor Fuel CAP Replacing and Cleaning AIR FilterSpark Plug Storage 1 Month or LongerProblem Possible Cause Solution TroubleshootingTroubleshooting Limited Warranty Statement WarrantyManufacturers Warranty Coverage Emissions Maintenance Schedule and Warranted Parts List Homelite Consumer PRODUCTS, INC

UT20005, UT20004, UT20025, UT20024, UT20045 specifications

Homelite, a trusted name in outdoor power equipment, offers a versatile range of string trimmers and brushcutters designed to meet the diverse needs of homeowners and professionals alike. The models UT20005, UT20045, UT20025, UT20004, and UT20044 showcase the brand's commitment to innovation and efficiency.

The Homelite UT20005 is a powerful electric string trimmer that is lightweight and easy to handle. Its 10-amp motor delivers a strong performance, making it ideal for tackling overgrown grass and weeds. This model features an adjustable shaft for user comfort and can easily convert to an edger, providing dual functionality in one tool. The automatic feed spool allows for continuous operation without interruptions, ensuring a seamless trimming experience.

The UT20045 model takes performance a step further with its robust design and advanced features. Equipped with a 5-amp motor, this trimmer is suitable for both residential and light commercial use. It offers a variable speed trigger that allows users to control the power according to the task at hand. The dual-line system enhances cutting efficiency, making it easier to handle tougher vegetation.

For those seeking a more compact option, the UT20025 model is lightweight yet powerful. Its ergonomic design minimizes user fatigue, making it ideal for extended use. The trimming width is adjustable, allowing for precise cutting in hard-to-reach areas. This model is particularly favored by gardeners and hobbyists who appreciate its ease of use.

Moving on to the UT20004, this model emphasizes user convenience with a straight shaft design that provides better reach and reduces the need for bending. The 2-in-1 capability allows for quick conversion from trimmer to edger. This feature is particularly valuable for those with smaller yards looking for efficient solutions without the need for multiple tools.

Lastly, the UT20044 model stands out with its focus on durability and performance. Built with robust materials, it features a high-capacity battery that offers extended run times, enhancing productivity without the hassle of cords. The innovative brushless motor technology ensures quieter operation and requires less maintenance, making it an excellent choice for eco-conscious consumers.

In summary, Homelite’s UT20005, UT20045, UT20025, UT20004, and UT20044 models exemplify reliability and innovation in outdoor power equipment. With features tailored for various cutting tasks, these string trimmers and brushcutters combine performance, ease of use, and technological advancements to accommodate the needs of both casual users and professionals in lawn care.