Husqvarna 326HS75, 326HS99 manual Emission Control Warranty Statement

Page 20

EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND

OBLIGATIONS

The EPA (U.S. Environmental Protection Agency), CARB (California Air Resources Board) and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2001 and later small off-road engine. In U.S., new small off- road engines must be designed, built and equipped to meet the federal or California stringent anti-smog standards. Husqvarna Forest & Garden must warrant the emission control system on your small off-road engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your small offroad engine.

Your emission control system includes parts such as the carburetor, the ignition system and catalytic converter.

Where a warrantable condition exists, Husqvarna Forest & Garden will repair your small off-road engine at no cost to you including diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE

The 2001 and later small off-road engines are warranted for two years. If any emission related part on your engine is defective, the part will be repaired or replaced by Husqvarna Forest & Garden.

OWNER’S WARRANTY

RESPONSIBILITIES

As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your Owner’s Manual. Husqvarna Forest & Garden recommends that you retain all receipts covering maintenance on your small off-road engine, but Husqvarna Forest & Garden cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

As the small off-road engine owner, you should, however, be aware that Husqvarna Forest & Garden may deny you warranty coverage if your small off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your small off-road engine to a Husqvarna Forest & Garden authorized servicing dealer as soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest & Garden at 1-800-487- 5963.

WARRANTY COMMENCEMENT DATE

The warranty period begins on the date small off-road engine is delivered.

LENGTH OF COVERAGE

Husqvarna Forest & Garden warrants to the initial owner and each subsequent purchaser that the engine is free from defects in materials and workmanship which cause the failure of a warranted part for a period of two years.

WHAT IS COVERED

REPAIR OR REPLACEMENT OF PARTS

Repair or replacement of any warranted part will be performed at no charge to the owner at an approved Husqvarna Forest & Garden servicing dealer.

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest & Garden at 1-800-487- 5963.

WARRANTY PERIOD

Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled only for regular inspection to the effect of ”repair or replace as necessary” shall be warranted for 2 years. Any warranted part which is scheduled for replacement as required maintenance shall be warranted for the period of time up to the first scheduled replacement point for that part.

DIAGNOSIS

The owner shall not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the diagnostic work is performed at an approved Husqvarna Forest & Garden servicing dealer.

CONSEQUENTIAL DAMAGES

Husqvarna Forest & Garden may be liable for damages to other engine components caused by the failure of a warranted part still under warranty.

WHAT IS NOT COVERED

All failures caused by abuse, neglect or improper maintenance are not covered.

ADD-ON OR MODIFIED PARTS

The use of add-on or modified parts can be grounds for disallowing a warranty claim. Husqvarna Forest & Garden is not liable to cover failures of warranted parts caused by the use of add- on or modified parts.

HOW TO FILE A CLAIM

If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized servicing dealer or call Husqvarna Forest & Garden at 1-800-487- 5963.

WHERE TO GET WARRANTY SERVICE

Warranty services or repairs shall be provided at all Husqvarna Forest & Garden authorized servicing dealers.

MAINTENANCE, REPLACEMENT AND REPAIR OF EMISSION-RELATED PARTS

Any Husqvarna Forest & Garden approved replacement part used in the performance of any warranty maintenance or repairs on emission-related parts, will be provided without charge to the owner if the part is under warranty.

EMISSION CONTROL WARRANTY PARTS LIST

1.Carburetor and internal parts

2.Intake pipe, airfilter holder and carburetor bolts.

3.Airfilter and fuelfilter covered up to maintainance schedule.

4.Ignition System

a)Spark Plug, covered up to maintenance schedule

b)Ignition Module

5.Muffler with catalytic converter

MAINTENANCE STATEMENT

The owner is responsible for the performance of all required maintenance, as defined in the operator’s manual.

20 – English

Image 20
Contents Operators manual Carb II, EPA EnglishSymbol Explanation SymbolsContents Machine’s protective equipment Safety InstructionsPersonal protective eqipment Vibration damping system MufflerCheck that the hand guard D is secured Gearbox Assembly of the catcher accessoryBlades Transport and storage General safety instructionsStart Fuel safety Safety instructions when using the hedge trimmer Personal protectionProtective instructions regarding the surroundings Protective instructions while workingProtective instructions when work is completed Basic working techniquesWhat is WHAT? What is what on the hedge trimmer?Fuelling Fuel HandlingFuel mixture Start and Stop Control before startingStart and stop StartMaintenance CarburetorHigh speed needle H Adjusting the idle speed, TCorrectly adjusted carburetor Muffler Cooling system Spark plugCleaning and lubrication Cleaning the air filterAir filter GearboxMaintenance schedule Daily maintenanceWeekly maintenance Monthly maintenanceTechnical Data Technical data 326HS75 326HS99Emission Control Warranty Statement English ´+H!¶33¨ English 114 00 2002W01

326HS99, 326HS75 specifications

The Husqvarna 326HS75 and 326HS99 are two advanced hedge trimmers designed for both professional landscapers and dedicated gardeners. These models exhibit a fusion of power, durability, and cutting-edge technology, providing an efficient solution for maintaining hedges and shrubs.

One of the most notable features of both models is their powerful engine. The Husqvarna 326HS75 comes equipped with a 24.5 cc, 1.0 kW two-stroke engine, while the 326HS99 is powered by a more robust 27.6 cc engine, delivering 1.1 kW of power. This allows users to tackle even the most resilient hedges with ease, achieving clean, precise cuts without straining the machine.

The innovative design of the cutting system is another highlight. Both models feature double-sided blades, designed for optimal cutting efficiency. The 26-inch long blades provide an extended reach, ideal for reaching high or wide hedges. The sharp, dual-action cutting design minimizes vibrations and enhances cutting speed, allowing users to work through dense foliage quickly.

In terms of comfort, both hedge trimmers incorporate ergonomic handles that reduce operator fatigue during prolonged use. They are designed with a lightweight structure, making them easy to maneuver. Additionally, the adjustable rear handle ensures a secure grip, providing better control in various cutting positions.

The 326HS75 and 326HS99 also showcase advanced technology to enhance performance. The LowVib technology minimizes vibrations typically experienced during operation, aiding in user comfort and safety. Furthermore, the Air Injection feature in both models ensures a clean air supply to the engine, which leads to improved performance and extended intervals between air filter cleaning.

For users concerned about environmental impact, both models adhere to stringent emission regulations, ensuring efficient fuel consumption while reducing harmful emissions. The fuel tank design allows for a transparent view of fuel levels, preventing unexpected downtime.

In summary, the Husqvarna 326HS75 and 326HS99 hedge trimmers are exemplary tools in the landscaping segment. Their combination of powerful engines, efficient cutting systems, ergonomic design, and innovative technologies make them ideal for anyone looking to achieve professional results while maintaining comfort and reducing environmental impact. Whether for commercial or residential use, these hedge trimmers provide the reliability and performance necessary to shape and define any garden space.