Husqvarna 325 L XT-Series, 325LD, 325C Start and Stop, Control before starting, Start and stop

Page 16

START AND STOP

Control before starting

For reasons of safety follow these recommendations!

Check that the support flange is not cracked due to

fatigue or due to being tightened too much. Discard the support flange if it is cracked.

Ensure the locking nut has not lost its captive force. The nut lock should have a locking force of at least 1.5 Nm. The tightening torque of the locking nut

should be 35-50 Nm.

Check that the trimmer head and spray guard are not damaged or cracked. Replace the trimmer head

or spray guard if they are exposed to impact or are cracked.

Never use the machine without a guard or spray guard nor with a defective guard.

Start and stop

!WARNING!

The complete clutch cover with shaft must be fitted before the machine is started, otherwise the clutch can become loose and cause personal injury.

Always move the machine from the filling area before starting. Place the machine on a flat surface. Ensure the cutting equipment cannot come into contact with any object. Make sure no unauthorised persons are in the working area, otherwise there is a risk of serious personal injury. The safety distance is 15 metres.

Cold engine

IGNITION:

Set the stop switch to the start position.

CHOKE:

Set the choke control in the choke position.

AIR PURGE: Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled.

Warm engine

Use the same starting procedure as for the cold engine, but do not set the choke control in the choke position. The start throttle position is obtained by setting the choke control in the choke position and then returning it to its original position.

Stop

The engine is stopped by switching off the ignition.

!WARNING!

When the engine is started with the choke in the choke or start position the cutting equipment starts to rotate immediately.

Start

Press the machine body against the ground using your left hand (NOTE! Not your foot). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord.

Reset the choke control as soon as the engine fires and repeat until the engine starts. When the engine starts quickly apply full throttle and the start throttle will automatically disengage.

NOTE! Do not pull the starter cord out completely and do not release the starter cord from the fully extended position. This can damage the machine.

16 – English

Image 16
Contents 322L 323L 325C 325CX-SERIES Symbol Explanation SymbolsContents Machine‘s safety equipment Safety InstructionsPersonal protective equipment Vibration damping system MufflerCutting Equipment Locking nutMaintenance Cutting equipment Trimmer headGeneral safety instructions Fuel safetyStart Transport and storageBasic safety precautions Grass trimming using the trimmer head and plastic knifesGeneral working instructions Basic working techniquesTrimming ClearingSweeping What is WHAT? What is what on the trimmer?Assembly Assembly of the trimmer headAssembling the loop handlebar 325C, 325CX AssemblingFitting the spray guard and trimmer head 325C Fit the appropriate guardFitting the spray guard and trimmer head 325CX Fuel mixture Fuel HandlingFuelling Control before starting Start and StopStart and stop Maintenance CarburetorCorrectly adjusted carburetor Final setting of the idling speed THigh speed needle Spark plug Muffler Cooling systemTwo-part shaft Air filter Maintenance scheduleAngle gear 322L, 323L, 325LX, 325LXT, 325LDX Technical Data Technical data 322L/323L325LX 325LXT 325LDXTechnical data 325C 322L, 323L, 325LX, 325LXT, 325LDX Approved accessories Type Attachments Art No Use withEmission Control Warranty Statement Your Warranty Rights ObligationsSuper Auto Super Auto II Tri Cut Trimmy H Click Trimmy Hit Junior Trimmy Hit Pro 2,4 mm 080-.095 12 cm ~ 3,5 m ~ 15 cm Trimmy SII English ´+Hy¶5h¨ English 114 00 2002W11