Husqvarna 326EX-Series manual Assembly, Assembling the blade, Assembling the angle gear

Page 13

 

 

 

 

 

 

 

ASSEMBLY

 

Assembling the loop handlebar

 

Assembling the blade

 

 

 

 

 

 

 

 

 

Fit the blade as follows:

 

 

 

 

• Position the handle on the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

shaft. Note that the handle

 

 

 

 

 

 

1. Fit the drive disc (A) on

 

 

 

must be mounted below the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

arrow on the shaft.

 

 

 

 

 

 

the outgoing shaft. Make

 

 

 

 

 

 

 

 

 

 

 

sure that the edge that fits

 

• Fit the bolt, securing plate

 

in the hole of the blade is

 

and wing nut as shown in the

 

facing outward.

 

diagram.

 

2. Block the blade rotation

 

 

 

 

 

 

 

 

 

 

• Tighten the wing nut.

 

by inserting locking pin in

 

 

the hole behind the blade

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

guard engaging it in the

 

 

 

 

 

 

 

 

 

corresponding hole in the

 

 

 

 

 

 

 

 

 

drive disc.

 

 

 

 

 

 

 

 

 

3. Fit the blade (B) on the

 

 

 

 

 

 

 

 

 

drive disc.

 

 

 

 

 

 

 

 

 

4. Fit the support

 

 

 

 

 

 

 

 

 

flange (C). The support

 

 

 

 

 

 

 

 

 

flange must be fitted with

 

 

 

 

 

 

 

 

 

its outer edge hard up

 

 

 

 

 

 

 

 

 

against the blade.

 

5. Fit the locknut (D). NOTE! The locknut has left-hand threads. The tightening torque of the locknut is 35

– 50 Nm.

6. Remove the locking pin.

Assembling the angle gear

 

• Assemble the angle gear

NOTE! Do not forget to remove the locking pin before using

back on the supporting tube.

Turn the blade so that the

the machine.

drive shaft engages in the

 

angle gear.

 

 

WARNING!

 

Under no circumstances may the edge cutter

• Position the angle gear so

! blade be used without the blade guard fitted.

 

that its slot is aligned with the

 

line on the supporting tube.

 

• Firmly tighten the screw.

English – 13

Image 13
Contents Operator’s manual Carb II, EPA Symbols Explanation of SymbolsContents Machine’s safety equipment Safety InstructionsPersonal protective equipment Muffler Vibration damping systemCutting equipment Locking nutSafety Instructions Safety Instructions Safety instructions regarding the surround- ings General safety instructionsSafety instructions before starting work Personal protectionStart Fuel safetyTransport and storage Safety instructions while working Basic safety precautionsGeneral working instructions Basic working techniquesSafety instructions after completing work What is what on the edger? What is WHAT?Assembling the blade AssemblyAssembling the angle gear Fuel mixture Fuel HandlingFuelling Control before starting Start and StopStart and stop StopCarburetor MaintenanceHigh speed needle H Correctly adjusted carburetor Final setting of the idling speed TCooling system Muffler with catalytic converterSpark plug Air filter Adjusting the edger‘s cutting depthLubricating the flexible drive axle Angle gearDaily maintenance Maintenance scheduleWeekly maintenance Monthly maintenanceTechnical data Technical DataYour Warranty Rights Obligations Emission Control Warranty StatementEnglish 2005W28 114 03 39