Husqvarna 323LD, 325LDX manual Working Techniques, General working instructions, Basic safety rules

Page 17

WORKING TECHNIQUES

General working instructions

IMPORTANT!

This section takes up the basic safety precautions for working with a trimmer.

If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop.

Avoid all usage which you consider to be beyond your capability.

You must understand the difference between forestry clearing, grass clearing and grass trimming before use.

Basic safety rules

1 Look around you:

To ensure that people, animals or other things cannot affect your control of the machine.

To ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting attachment.

CAUTION! Do not use the machine unless you are able to call for help in the event of an accident.

2Inspect the working area. Remove all loose objects, such as stones, broken glass, nails, steel wire, string, etc. that could be thrown out or become wrapped around the cutting attachment.

3Do not use the machine in bad weather, such as dense fog, heavy rain, strong wind, intense cold, etc. Working in bad weather is tiring and often brings added risks, such as icy ground, unpredictable felling direction, etc.

4Make sure you can move and stand safely. Check the area around you for possible obstacles (roots, rocks, branches, ditches, etc.) in case you have to move suddenly. Take great care when working on sloping ground.

5 Keep a good balance and a firm foothold.

6Always hold the machine with both hands. Hold the machine on the right side of your body.

7Keep the cutting attachment below waist level.

8Switch off the engine before moving to another area. Fit the transport guard before carrying or transporting the equipment any distance.

9Never put the machine down with the engine running unless you have it in clear sight.

WARNING! Neither the operator of the

!machine nor anyone else may attempt to remove the cut material while the engine is running or the cutting equipment is rotating, as this can result in serious injury.

Stop the engine and cutting equipment before you remove material that has wound around the blade shaft as otherwise there is a risk of injury. The bevel gear can get hot during use and may remain so for a while afterwards. You could get burnt if you touch it.

WARNING! Watch out for thrown objects.

!Always wear approved eye protection. Never lean over the cutting attachment guard. Stones, rubbish, etc. can be thrown up into the eyes causing blindness or serious injury.

Keep unauthorised persons at a distance. Children, animals, onlookers and helpers should be kept outside the safety zone of 15 m. Stop the machine immediately if anyone approaches. Never swing the machine around without first checking behind you to make sure no-one is within the safety zone.

Basic working techniques

Always slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage.

WARNING! Sometimes branches or grass

!get caught between the guard and cutting attachment. Always stop the engine before cleaning.

English – 17

Image 17
Contents 323L 323LD 325CX 325LX 325LDX Symbols KEY to SymbolsContents Dear Customer IntroductionWhat is what? What is WHAT?Personal protective equipment General Safety PrecautionsThrottle lock Machine′s safety equipmentStop switch Muffler Cutting attachment guardVibration damping system Trimmer head Cutting equipmentLocking nut Assembly AssemblyFitting the loop handle Assembling and dismantling the two-piece shaftFitting other guards and cutting attachments Fitting the trimmer headGuard Fitting the trimmer guard and trimmer headFuel Fuel safetyFuel Handling Mixing FuellingCheck before starting Starting and StoppingStarting and stopping StartingStopping Working Techniques Basic safety rulesGeneral working instructions Basic working techniquesTrimming Grass trimming with a trimmer headCarburettor MaintenanceCorrectly adjusted carburettor Fine adjustment of the idle speed TMuffler High speed jet HCooling system Cleaning the air filterSpark plug Two-piece shaftBevel gear Oiling the air filterMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataTechnical data 325Cx 325Lx 325LDx Engine Attachments Art No Use with EC-declaration of conformity Applies to Europe onlySuper Auto Super Auto II Page S35 25 m T35 T25 T25C ´z+R-T¶63¨ Page 1150135-26 ´z+R-T¶63¨´z+R-T¶63¨2005-10-25