Ryobi 890r manual Rules For Safe Operation, Important Safety Information, Read All Instructions

Page 4
RULES FOR SAFE OPERATION

RULES FOR SAFE OPERATION

The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.

SYMBOL MEANING

SAFETY ALERT SYMBOL: Indicates danger, warning, or caution. Attention is required in order to avoid serious personal injury. May be used in conjunction with other symbols or pictographs.

NOTE: Advises you of information or instructions vital to the operation or maintenance of the equipment.

DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock, and personal injury.

WARNING: Failure to obey a safety warning can result in injury to yourself and others. Always follow the safety precautions to reduce the risk of fire, electric shock, and personal injury.

CAUTION: Failure to obey a safety warning may result in property damage or personal injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock, and personal injury.

• IMPORTANT SAFETY INFORMATION •

READ ALL INSTRUCTIONS

BEFORE OPERATING

Read the instructions carefully. Be familiar with the controls and proper use of the unit.

Do not operate this unit when tired, ill, or under the influence of alcohol, drugs, or medication.

Children and teens under the age of 15 must not use the unit, except for teens guided by an adult.

Inspect the unit before use. Replace damaged parts. Check for fuel leaks. Make sure all fasteners are in place and secure. Replace cutting attachment parts that are cracked, chipped, or damaged in any way. Make sure the cutting attachment is properly installed and securely fastened. Be sure the cutting attachment shield is properly attached, and positioned as recommended. Failure to so can result in personal injury to the operator and bystanders, as well as damage to the unit.

Use only 0.095 inch (2.41 mm) diameter genuine Ryobi replacement line. Never use metal-reinforced line, wire, or rope, etc. These can break off and become a dangerous projectile.

Be aware of the risk of injury to the head, hands and feet.

Clear the area to be cut before each use. Remove all objects such as rocks, broken glass, nails, wire, or string which can be thrown or become entangled in the cutting attachment. Clear the area of children, bystanders, and pets. At a minimum, keep all children, bystanders and pets outside a 50 feet (15 m) radius; there still may be a risk to bystanders from thrown objects. Bystanders should be encouraged to wear eye protection. If you are approached, stop the engine and cutting attachment immediately.

Squeeze the throttle control and check that it returns automatically to the idle position. Make all adjustments or repairs before using unit.

SAFETY WARNINGS FOR GAS TRIMMERS

WARNING: Gasoline is highly flammable, and its vapors can explode if ignited. Take the following precautions:

Store fuel only in containers specifically designed and approved for the storage of such materials.

Always stop the engine and allow it to cool before filling the fuel tank. Never remove the cap of the fuel tank, or add fuel, when the engine is hot. Never operate the unit without the fuel cap securely in place. Loosen the fuel tank cap slowly to relieve any pressure in the tank.

Add fuel in a clean, well-ventilated area outdoors where there are no sparks or flames. Slowly remove the fuel cap only after stopping engine. Do not smoke while fueling or mixing fuel. Wipe up any spilled fuel from the unit immediately.

Avoid creating a source of ignition for spilled fuel. Do not start the engine until fuel vapors dissipate.

Move the unit at least 30 feet (9.1 m) from the fueling source and site before starting the engine. Do not smoke, keep sparks and open flames from the area while adding fuel or operating the unit.

WHILE OPERATING

Never start or run the unit inside a closed room or building. Breathing exhaust fumes can kill. Operate this unit only in a well ventilated area outdoors.

Wear safety glasses or goggles that are marked as meeting ANSI Z87.1 standards, and ear/hearing protection when operating this unit. Wear a face or dust mask if the operation is dusty.

Wear heavy, long pants, boots, gloves and a long sleeve shirt. Do not wear loose clothing, jewelry, short pants, sandals or go barefoot. Secure hair above shoulder level.

4

Image 4
Contents IMPORTANT MANUAL FOR QUESTIONS, CALL 1-800-345-8746 in U.S. orOPERATOR’S MANUAL 890r 4-Cycle Gas Trimmer/BrushcutterTABLE OF CONTENTS PRODUCT REFERENCES, ILLUSTRATIONS AND SPECIFICATIONSSERVICE INFORMATION INTRODUCTIONCALIFORNIA EMISSION REGULATIONS SPARK ARRESTORCalifornia Proposition 65 Warning THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS CHEMICALSIMPORTANT SAFETY INFORMATION SYMBOL MEANINGSAFETY WARNINGS FOR GAS TRIMMERS RULES FOR SAFE OPERATIONWHILE OPERATING WITH CUTTING BLADE AFTER USEOTHER SAFETY WARNINGS SAFETY AND INTERNATIONAL SYMBOLSSYMBOLMEANING SAFETY ALERT SYMBOL FOR SERVICE INFORMATION, CALLSYMBOLMEANING OIL TRIMMER/BRUSHCUTTER SAFETYTHROWN OBJECTS AND ROTATING CUTTER CAN CAUSE SEVERE INJURY ON/OFF STOP CONTROLKNOW YOUR UNIT APPLICATIONSINSTALLING AND ADJUSTING THE J-HANDLE ASSEMBLY INSTRUCTIONSINSTALLING THE HARNESS REMOVING AND INSTALLING CUTTING ATTACHMENT SHIELD REMOVE THE CUTTING ATTACHMENT AND INSTALL THE CUTTING BLADEInstall the Cutting Blade Remove the Cutting Attachment ShieldREMOVE THE CUTTING BLADE AND INSTALL THE CUTTING ATTACHMENT Remove the Cutting BladeOIL AND FUEL INFORMATION RECOMMENDED OIL TYPEInstall the Cutting Attachment ADDING OIL TO CRANKCASE - INITIAL USEFUELING UNIT RECOMMENDED FUEL TYPEUsing Blended Fuels Using Fuel AdditivesSTARTING/STOPPING INSTRUCTIONS STARTING INSTRUCTIONSOPERATING INSTRUCTIONS STOPPING INSTRUCTIONSOPERATING THE CLICK-LINK SYSTEM Installing the Cutting Attachment or Add-OnsHOLDING THE TRIMMER ADJUSTING TRIMMING LINE LENGTHTIPS FOR BEST TRIMMING RESULTS DECORATIVE TRIMMING USING THE CUTTING BLADECutting Blade Operating Tips MAINTENANCE AND REPAIR INSTRUCTIONS MAINTENANCE SCHEDULEMAINTENANCE REQUIRED LINE INSTALLATIONINSTALLING A PREWOUND REEL Replacement PartsCHANGING THE OIL CHECKING THE OIL LEVELCAUTION Wear gloves to prevent injury when handling the unit AIR FILTER MAINTENANCE Cleaning the Air FilterCARBURETOR ADJUSTMENT ROCKER ARM CLEARANCEClean Air Filter Adjust Idle Speed Screw3. Remove the screw on back of the engine cover Fig ACCESSORIES/REPLACEMENT PARTS SPARK ARRESTOR MAINTENANCEREPLACING THE SPARK PLUG CLEANING AND STORAGE CLEANINGSTORAGE LONG TERM STORAGETROUBLESHOOTING ENGINE LACKS POWER OR STALLS WHEN CUTTINGENGINE WILL NOT START ENGINE WILL NOT IDLEENGINE SPECIFICATIONSDRIVE SHAFT & CUTTING ATTACHMENT Page CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONSOWNERS WARRANTY RESPONSIBILITIES MANUFACTURERS WARRANTY COVERAGELIMITED TWO-YEAR WARRANTY SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCERYOBI OUTDOOR PRODUCTS RYOBI CANADA INC