Ryobi 890r Replacing The Spark Plug, Spark Arrestor Maintenance, Accessories/Replacement Parts

Page 24
REPLACING THE SPARK PLUG

MAINTENANCE AND REPAIR INSTRUCTIONS

REPLACING THE SPARK PLUG

Use only genuine Ryobi spark plugs. The correct air gap is 0.025 in. (0.655 mm). Remove the plug after every 50 hours of operation and check its condition.

1.Stop the engine and allow it to cool. Grasp the plug wire firmly and pull the cap from the spark plug.

2.Clean dirt from around the spark plug. Remove the spark plug from the cylinder head by turning counterclockwise using a 5/8 inch deep socket.

3.Replace cracked, fouled or dirty spark plug. Set the air gap at 0.025 in. (0.655 mm) using a feeler gauge (Fig. 55).

0.025 in.

(0.655 mm.)

Fig. 55

CAUTION: Do not sand blast, scrape, or clean electrodes. Grit in the engine could damage the cylinder.

4.Install a correctly gaped spark plug in the cylinder head. Tighten by turning the 5/8 inch deep socket clockwise until snug.

If using a torque wrench torque to; 110-120 in.•lb. (12.3-13.5 N•m). Do not over tighten.

SPARK ARRESTOR MAINTENANCE

1.Remove the muffler cover. See Rocker Arm Clearance, Pg. 22.

2.With a flat blade screwdriver or Torx T20 bit, remove the screw attaching the spark arrestor cover to the muffler (Fig. 56).

Muffler

Spark Arrestor Screen

Tab Screw

Spark Arrestor Cover

Slot

Fig. 56

3.Pull the tab on the spark arrestor cover out of the muffler. Remove the spark arrestor cover.

4.Remove the spark arrestor screen from the spark arrestor cover.

5.Clean the spark arrestor screen with a wire brush, or replace.

6.Reinstall the spark arrestor screen, spark arrestor cover, and screw.

ACCESSORIES/REPLACEMENT PARTS

4-Cycle Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181786

Oil Fill Plug / Dipstick . . . . . . . . . . . . . . . . . . . . . 182378

Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180852

Spark Arrestor Screen . . . . . . . . . . . . . . . . . . . . . 180890

Replacement Line . . . . . . . . . . . . . . . . . . . . . . . . 612454

Replacement Line Cartridge . . . . . . . . . . . . . . . . 147345

Inner Reel Spring . . . . . . . . . . . . . . . . . . . . . . . . 610636

Outer Spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 683301

Inner Reel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147495

Bump Knob™ . . . . . . . . . . . . . . . . . . . . . . . . . . . 180814

Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 181083

Shoulder Harness . . . . . . . . . . . . . . . . . . . . . . . . 682075

Click-Link Coupler . . . . . . . . . . . . . . . . . . . . . . . 181616

These replacement parts can be purchased from your local authorized dealer.

24

Image 24
Contents IMPORTANT MANUAL FOR QUESTIONS, CALL 1-800-345-8746 in U.S. orOPERATOR’S MANUAL 890r 4-Cycle Gas Trimmer/BrushcutterTABLE OF CONTENTS PRODUCT REFERENCES, ILLUSTRATIONS AND SPECIFICATIONSSERVICE INFORMATION INTRODUCTIONCALIFORNIA EMISSION REGULATIONS SPARK ARRESTORCalifornia Proposition 65 Warning THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS CHEMICALSIMPORTANT SAFETY INFORMATION SYMBOL MEANINGSAFETY WARNINGS FOR GAS TRIMMERS RULES FOR SAFE OPERATIONWHILE OPERATING WITH CUTTING BLADE AFTER USEOTHER SAFETY WARNINGS SAFETY AND INTERNATIONAL SYMBOLSSYMBOLMEANING SAFETY ALERT SYMBOL FOR SERVICE INFORMATION, CALLSYMBOLMEANING OIL TRIMMER/BRUSHCUTTER SAFETYTHROWN OBJECTS AND ROTATING CUTTER CAN CAUSE SEVERE INJURY ON/OFF STOP CONTROLKNOW YOUR UNIT APPLICATIONSASSEMBLY INSTRUCTIONS INSTALLING AND ADJUSTING THE J-HANDLEINSTALLING THE HARNESS REMOVING AND INSTALLING CUTTING ATTACHMENT SHIELD REMOVE THE CUTTING ATTACHMENT AND INSTALL THE CUTTING BLADEInstall the Cutting Blade Remove the Cutting Attachment ShieldREMOVE THE CUTTING BLADE AND INSTALL THE CUTTING ATTACHMENT Remove the Cutting BladeOIL AND FUEL INFORMATION RECOMMENDED OIL TYPEInstall the Cutting Attachment ADDING OIL TO CRANKCASE - INITIAL USEFUELING UNIT RECOMMENDED FUEL TYPEUsing Blended Fuels Using Fuel AdditivesSTARTING/STOPPING INSTRUCTIONS STARTING INSTRUCTIONSOPERATING INSTRUCTIONS STOPPING INSTRUCTIONSOPERATING THE CLICK-LINK SYSTEM Installing the Cutting Attachment or Add-OnsADJUSTING TRIMMING LINE LENGTH HOLDING THE TRIMMERTIPS FOR BEST TRIMMING RESULTS USING THE CUTTING BLADE DECORATIVE TRIMMINGCutting Blade Operating Tips MAINTENANCE AND REPAIR INSTRUCTIONS MAINTENANCE SCHEDULEMAINTENANCE REQUIRED LINE INSTALLATIONINSTALLING A PREWOUND REEL Replacement PartsCHECKING THE OIL LEVEL CHANGING THE OILCAUTION Wear gloves to prevent injury when handling the unit AIR FILTER MAINTENANCE Cleaning the Air FilterCARBURETOR ADJUSTMENT ROCKER ARM CLEARANCEClean Air Filter Adjust Idle Speed Screw3. Remove the screw on back of the engine cover Fig SPARK ARRESTOR MAINTENANCE ACCESSORIES/REPLACEMENT PARTSREPLACING THE SPARK PLUG CLEANING AND STORAGE CLEANINGSTORAGE LONG TERM STORAGETROUBLESHOOTING ENGINE LACKS POWER OR STALLS WHEN CUTTINGENGINE WILL NOT START ENGINE WILL NOT IDLESPECIFICATIONS ENGINEDRIVE SHAFT & CUTTING ATTACHMENT Page CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONSOWNERS WARRANTY RESPONSIBILITIES MANUFACTURERS WARRANTY COVERAGELIMITED TWO-YEAR WARRANTY SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCERYOBI OUTDOOR PRODUCTS RYOBI CANADA INC