Snapper LT160H42GBV, LT160H42GBV2, WLT180H48GBV2, WLT160H42GBV, WLT180H48GBV2 Tractor Lubrication

Page 13

Section 3 - MAINTENANCE

3.2.4.CHECK DECK DRIVE BELT

1.The idler and spring provide proper belt tension and require no adjustment. If belt is frayed, slit, severed or belt strands exposed, replace belt before operating mower.

3.3SEVICE - EVERY 25 OPERATING HOURS

3.3.1.CHECK ENGINE

1.Change engine oil. Refer to Section “CHANGE ENGINE OIL”. Refer to engine owner's manual for oil specification.

2.Remove and clean engine air pre-cleaner. See Figure 3.4. Refer to engine owner's manual for cleaning instructions.

3.Remove and replace engine air cleaner. Refer to engine owner's manual for service instructions.

COVER RETAINING

KNOB

AIR CLEANER COVER

ELEMENT RETAINING KNOB

CARTRIDGE ELEMENT

PRE-CLEANER

RETAINING STUD

AIR CLEANER BASE

SINGLE CYLINDER ENGINE TYPE

AIR CLEANER BASE

CARTRIDGE ELEMENT

PRE-CLEANER

RETAINING KNOB

RETAINING PLATE

AIR CLEANER COVER

COVER RETAINING CLIPS

TWIN CYLINDER ENGINE TYPE

FIGURE 3.4

3.3.2.MOWER COMPONENTS

1.Check deck drive belt for proper tension. Refer to Section, “CHECK DECK DRIVE BELT”.

2.Check blades for sharpness, wear, damage and torque. Refer to Section on “MOWER BLADE SERVICE”.

3.Check mower deck for proper levelness. Refer to Section “MOWER DECK ADJUSTMENT -

LEVELNESS”.

4.Clean mower deck.

a.Remove key from ignition switch.

b.Remove deck.

c.Clean underside of mower deck, removing all accumulation of grass clippings and debris.

d.Clean top of deck, removing all grass clippings and debris.

5.Lubricate spindles with 1 to 3 shots of general purpose grease from grease gun.

IMPORTANT - 48” DECK ONLY:

Spindles on 48” deck must be kept filled with grease. Apply grease from grease gun until grease purges from vent located underneath deck on spindle housing.

6.Lubricate all mower deck linkage pivot points with a light coat of motor oil.

3.3.3.CHECK BLADE BRAKE

1.Refer to Section “CHECK BLADE BRAKE”.

3.3.4.TRACTOR LUBRICATION

1. Front Wheel Bearings

Lubricate each front wheel bearing through the grease fitting on wheel hub. Using general purpose grease in a grease gun, add grease until grease purges from bearing. See Figure 3.5.

AXLE SPINDLE

LUBRICATION

FITTING

FRONT WHEEL

BEARING LUBRICATION

FITTING

FIGURE 3.5

2. Axle Spindles

Lubricate each axle spindle with 1 to 3 shots of general purpose grease. See Figure 3.5.

(Continued On Next Page)

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents 160 Model Number ExplanationImportant Safety Instructions Operation Table of Contents Components Controls FamiliarizationOPERATOR’S Seat Adjustment Front to Rear Adjustment PRE-START ChecklistStarting & Operation Starting Engine Starting Wheel Drive Starting & OperationStarting Mower Blade Stopping ENGINE, BLADE, Wheel Drive 2.4.1. Stopping EngineCutting Height Adjustment Setting Park BrakeStopping Stopping Mower Blades Releasing Park BrakeRolling Tractor with Engine OFF 2.6.1. Rolling Hydro Models Reverse Lockout Mechanism Override Reverse Lockout MechanismIntroduction Service After First 5 HoursChange Engine OIL Check Blade BrakeSevice Every 25 Operating Hours Check Engine Check Deck Drive BeltSingle Cylinder Engine Type Twin Cylinder Engine Type Mower ComponentsSteering Sector Gear Tractor Lubrication From Previous Clutch/Brake PivotSteering Shaft Steering Drag LinkEngine Annually END of Each SeasonFuel Filter Spark Plug Hydrostatic Transmission OILBlade Brake Adjustment Engine Adjustments & RepairBlade Belt Adjustment Mower Deck Adjustment Levelness 1. SIDE-To-SIDE 42 DecksClevis TOP View of Deck Mower Deck Adjustment Levelness SIDE-To-SIDE 48 DecksFront To Rear Mower Deck Adjustment LevelnessSteering Adjustment Tractor Drive Components Brake AdjustmentShifter Adjustment Mower Blade Service Standard Blade Wear Limits Traction Drive Belt AdjustmentStandard Blade Sharpening Ninja Blade Wear LimitsNinja Blade Sharpening Mower Blade Replacement Mower Deck Removal Traction Drive Belt ReplacementDeck Shown View from Underneath Tractor Traction drive belt replacementBell Crank Adjustment & Repair Tension Idler Spring Remove Spring from TOP View Mower Deck Battery Installation Battery Battery RemovalBattery Service Battery StorageNEW Battery Preparation Battery TestingRemove NUT Remove Belt from Spindle Remove Blade Bolt Available AccessoriesLT160H42GBV LT180H48GBV2 LT160H42GBV2Electrical System Problem Probable Cause Corrective Action Troubleshooting GuideTroubleshooting Guide LT160H42FBV NinjaDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Lawn Tractor Hydrostatic Drive Electric Clutch Series G

LT160H48GBV, LT160H42GBV2, LT180H48GBV2, WLT160H42GBV, WLT180H48GBV2, LT160H42GBV, LT160H42GBV2, WLT180H48GBV2, WLT160H42GBV, WLT180H48GBV2 specifications

The Snapper LT160H42GBV and its related models, including LT160H42GBV2, WLT180H48GBV2, WLT160H42GBV, and WLT180H48GBV2, are part of Snapper's renowned lineup of riding lawn mowers. These machines are designed for both residential and commercial users, delivering remarkable performance, efficiency, and versatility.

One of the key features of the Snapper LT series is the powerful engine. Most models are equipped with reliable Kohler or Briggs & Stratton engines, providing exceptional cutting power and durability. With a cutting deck range of 42 to 48 inches, the LT series allows users to tackle various lawn sizes and types with ease, ensuring a smooth and efficient mowing experience.

Another standout characteristic is the easy-to-use Gear-Driven Transmission system. This feature enables users to shift effortlessly between forward and reverse speeds, enhancing maneuverability around obstacles and tight spaces. Furthermore, the adjustable cutting height settings allow for a customized mowing experience, letting users choose their preferred grass height from a convenient range of settings.

The Snapper LT series also emphasizes comfort and ergonomics. The plush high-back seats provide ample cushioning, allowing users to mow for extended periods without discomfort. The large, easy-grip steering wheel enhances control, while the spacious footwell accommodates a variety of user sizes.

In terms of technology, the LT160H42GBV and its counterparts feature Snapper’s innovative SmartCharger technology that ensures the battery is always charged and ready to go. This is particularly useful for those who may not use their mower frequently, ensuring reliability every time you start the engine.

Safety is also a priority with these models. They come equipped with safety features such as operator presence control, which ensures that the mower will only operate when the driver is seated, preventing accidental starts.

In conclusion, the Snapper LT160H42GBV and its variants stand out for their robust engine performance, user-friendly controls, and comfort-oriented design. With modern technologies like SmartCharger and an array of safety features, these riding mowers provide an ideal solution for maintaining your lawn efficiently and effectively. Whether for home use or professional landscaping, the Snapper LT series delivers quality and reliability that users can trust.
Top Page Image Contents