Snapper ESPV21, ESPV21S Installation of Side Discharge, Deflector, Installation of Grass BAG

Page 10

Section 2 - OPERATING INSTRUCTIONS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

2.6 INSTALLATION OF SIDE DISCHARGE

DEFLECTOR

STEP 1: Remove recycling cover. Refer to Section

“Recycling Operation”.

STEP 2: Install deflector to deck in place of recycling cover,

making sure that: 1) front hole on outside front of deflector

fits over stud where front of recycling cover was originally

secured, 2) slot on top of deflector slips under restraining

nut on top of deck (under right front corner of engine), and

REAR SLOT OVER STUD; INSTALL LOCK WASHER AND KNOB NUT

ROUTE RECOIL ROPE

AROUND PULLEY

TOP

SLOT

UNDER NUT

 

FRONT HOLE

 

OVER STUD;

 

INSTALL LOCK

FIGURE 2.13

WASHER AND

KNOB NUT

3) slot on inside rear of deflector slips onto stud behind rear

of discharge opening, where rear of recycling cover was

originally secured. Install internal/external tooth lock

washers and knob nuts onto studs and tighten securely.

See Figure 2.12.

2.8 INSTALLATION OF GRASS BAG

(Door Type Bag)

STEP 1: Install grass bag adapter. Refer to Section

“Installation of Grass Bag Adapter”.

STEP 2: Install grass bag by opening adapter cover

(not shown) and sliding connector over adapter

flange. See Figure 2.14.

REAR SLOT OVER STUD; INSTALL LOCK WASHER AND KNOB NUT

TOP

SLOT

UNDER NUT

FRONT HOLE

OVER STUD;

INSTALL LOCK

WASHER AND

KNOB NUT

STEP 3: Attach grass bag hooks over middle handle

cross bar. See Figure 2.14.

HOOK DOOR AND

BAG HOOKS TO

MIDDLE HANDLE

SLIDE CONNECTOR

OVER FLANGE

FIGURE 2.12

2.7INSTALLATION OF GRASS BAG ADAPTER (Optional Accessory on Some Models)

STEP 1: Remove recycling cover. Refer to Section “Recycling Operation”.

STEP 2: Install grass bag adapter to the deck in place of

recycling cover, making sure that: 1) front hole on outside front of adapter fits over stud where front of recycling cover was originally secured, 2) slot on top of adapter slips under restraining nut on top of deck (under right front corner of engine), and 3) slot on bottom rear of adapter slips onto stud behind rear of discharge opening, where rear of recycling cover was originally secured. Install internal/external tooth lock washers and knob nuts onto studs and tighten securely. See Figure 2.13.

STEP 3: Route recoil rope around outside of rope guide

pulley. See Figure 2.13. (NOTE: Recoil rope may need to be slackened. Refer to “Handle Assembly”.)

FIGURE 2.14

WARNING

DO NOT operate without entire Grass Catcher or guard in place. Grass Catcher components are subject to deterioration during normal use. Inspect frequently and replace worn or damaged components immediately.

Grass Catcher bags used on SNAPPER products are made of woven fabric, and are subject to deterioration and wear during normal usage. Check condition of bag before each use. Immediately replace worn or damaged catcher bags with only bags recommended by SNAPPER. The grass catcher is optional equipment on some models.

10

Image 10
Contents Cutting Width European Model Self Propelled Model ‘Easy Line’Option Designation Variable SpeedImportant Safety Instructions From Previous ColumnFrom Previous Do not refuel the machine indoorsImportant Safety Instructions Table of Contents Model ESPV21 Shown Introduction FamiliarizationNomenclature Engine & Blade Operating InstructionsPRE-START Check List Starting & Operation Ground speed control to insure they work freely. SeeStarting & Operation Propelling Mower Handle Height AdjustmentStopping Recycling Operation Cutting Height AdjustmentEach Notch Raises CUT To Remove Recycling CoverDeflector Installation of Side DischargeInstallation of Grass BAG Door Type BagService Periodic MaintenanceService After First 5 Hours 3.2.1. Change Engine OIL Check Mower BladeStorage Procedure Mower Blade Replacement Standard Blade Wear Limit Repair & AdjustmentsBlade Sharpening Wheel Drive Control Adjustment Top of transmission pulley removed for clarityTo decrease minimum ground speed To adjust idler spring tensionTo increase minimum ground speed Belt Service Engine Drive Belt Replacement 1. Empty fuel tankFasteners Rear Cover Troubleshooting Problem Probable Cause Corrective ActionMAINTENANCE/REPLACEMENT Parts Service ScheduleService Performed Each USE HRS SeasonDecal Identification 3000 CE Compliance SpecificationsESPV21 ESPV21SYear Limited Warranty Disclaimer of WarrantyPage European 21 ‘EASY LINE’ Walk Behind Mowers

ESPV21, ESPV21S specifications

The Snapper ESPV21 and ESPV21S are innovative lawn care solutions designed to bring efficiency and power to your mowing experience. Both models are built with advanced features that enhance performance, making them exceptional choices for homeowners seeking reliable and effective lawn maintenance tools.

One of the standout features of the Snapper ESPV21 is its powerful engine. The mower is equipped with a robust Briggs & Stratton engine that delivers reliable performance and starts easily even in challenging weather conditions. The ESPV21S takes things a step further with a larger engine option, providing additional power for tackling thicker grass and tougher terrain.

The design of both mowers emphasizes ease of use. The Quick-Switch height adjustment system allows users to easily customize their mowing height with a simple lever, ensuring that you can achieve the perfect cut for your lawn. This feature is particularly beneficial for adapting to different grass types and seasonal growth patterns.

Another significant characteristic is the cutting deck design. The Snapper ESPV21 and ESPV21S feature a 21-inch steel cutting deck that offers durability and a clean cut. This deck is not only designed for efficiency but also promotes excellent grass collection, reducing the need for additional cleaning after mowing. With their mulching capabilities, these mowers can finely chop grass clippings, returning essential nutrients back to the soil.

User comfort is also a priority in the Snapper ESPV21 and ESPV21S models. Both mowers come with adjustable ergonomic handles, allowing users to find a comfortable grip position. The foldable design makes them easy to store in tight spaces, a convenience that is greatly appreciated by many homeowners.

In terms of technology, these mowers incorporate Snapper's patented Hi-Vac technology, which enhances suction and grass collection performance. This feature ensures that grass clippings are efficiently collected, resulting in a tidy lawn with minimal effort.

Safety is another important consideration, and both models are equipped with cutting-edge safety features, including a safety blade brake system that ensures the mower stops quickly if needed. This adds an extra layer of protection for users, making them suitable for families.

In conclusion, the Snapper ESPV21 and ESPV21S are excellent lawn mowers known for their power, efficiency, and user-friendly design. With advanced features such as a durable cutting deck, powerful engines, and innovative technologies, both models offer a reliable solution for maintaining a beautiful lawn throughout the seasons. Whether you have a small yard or a more extensive landscape, these mowers provide the performance and versatility needed for effective lawn care.