Snapper ERZT20441BVE2 manual Mower Deck Leveling, Orient Blades Side-to-Side

Page 29

Troubleshooting, Adjustments, & Service

Figure 27. Orient Blades Side-to-Side

MOWER DECK LEVELING

Perform these adjustments on a flat level surface. Be sure to check and adjust tire pressures before leveling the mower deck

SIDE-TO-SIDE LEVELING

1.With the mower installed, place the rider on a smooth, level surface such as a concrete floor. Turn the front wheels so they are straight.

2.Check for bent blades and replace if necessary.

3.Place the mower cutting height lever in the fourth adjustment notch from the bottom. Arrange the out- side mower blades so that they are pointing from side-to-side (Figure 27).

4.Measure the distance between the outside tips of each blade and the ground (Figures 27 & 28). The measurement should be 3” (7,6 cm), +/-1/8” (3mm). If there is more than 1/8” (3mm) difference between the measurements on each side, proceed to step 5. If the difference is 1/8” (3mm) or less, proceed to step 6.

5.Use the rear leveling nuts (A, Figure 29) to adjust the side-to-side leveling of the deck. Repeat step 4 if necessary.

FRONT-TO-BACK LEVELING

6.Arrange the blades so they face front-to-back (Figure 30).

7.Measure the distance from the ground to the front tip of the center blade and from the ground to the rear tip of the rear blades (Figures 28 & 30). The front tip of the front blade should be 1/4" (6mm) higher than the rear tips of the rear blades. If not, proceed with steps 8 - 9.

A

B

C

Figure 28. Measure Blade Tips to Ground

A.

Mower Deck

C. Level Ground

B.

Blade Tip

 

A

Figure 29. Mower Leveling - Side-to-Side A. Rear Leveling Nuts

(Left side shown, right side hidden)

Figure 30. Orient Blades Front-to-Back

(Continued Next Page)

28

Page 28 Page 30
Image 29
Page 28 Page 30
Contents OPERATOR’S Manual Table of Contents Safety Rules & Information Safety Rules and Information Towing CE Identification TAG Markings Identification NumbersSafety Decals Safety DecalsOperational Safety Checks Safety Interlock SystemChoke Control FunctionsMotion Control Levers PTO Switch Ignition SwitchSeat Adjustment Knobs Mower Cutting Height Adjustment LeverChecks Before Starting General Operating SafetyStopping the Rider & Engine Starting the EnginePushing the Rider by Hand MowingSmooth Travel Zero Turn Driving PracticeForward Travel Practice Reverse Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerRemoval Mower Removal InstallationAttaching a Trailer Installation Before Every Spring Each Hours 100 250 Fall Use Regular MaintenanceGrease LubricationServicing the Mower Blades Service Interval Every 10 Hours or As RequiredCheck Tire Pressures Engine MaintenanceChecking / Adding Fuel Fuel FilterStorage Battery MaintenanceCleaning the Battery and Cables Troubleshooting the Rider Troubleshooting, Adjustments, & ServiceTroubleshooting the Mower Troubleshooting, Adjustments, & ServiceMotion Control Lever Adjustment Seat AdjustmentsSpeed Balancing Adjustment Seat Position AdjustmentRoller BAR Adjustment Motion Control Lever Friction AdjustmentCutting Height Adjustment Neutral Adjustments Brake Adjustment Parking Brake AdjustmentFront Suspension Adjustment Select Models Blade Brake Check PTO Clutch AdjustmentOrient Blades Side-to-Side Mower Deck LevelingIf Equipped Deck Timing ROD AdjustmentRoller BAR Leveling Battery Charging Transmission Drive Belt ReplacementPRY Belts Over Pulleys Mower Belt ReplacementFuse Replacement Dimensions CE Compliance Specifications TransmissionsEngine ChassisTechnical Manuals Replacement PartsMaintenance Items
Top Page Image Contents