Snapper EMRP216017B Check Mower Blade, Check Engine Drive Belt, Check Transmission POLY-V Belt

Page 10

Section 3 - MAINTENANCE

3.2.2. CHECK GREASE LEVEL IN TRANSMISSION

NOTE: Do not spill grease or oil on surface of drive disc. See Figure 3.3.

3.Reinstall transmission plug.

4.Check grease level after each 25 hours of operation.

KEEP DRIVE DISC CLEAN !

FIGURE 3.3

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

IMPORTANT: DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

3.2.3. CHECK MOWER BLADE

1.Disconnect spark plug wire and secure end away from plug.

2.Tilt mower up on its rear wheels for access to the blade cap screw. Do not tilt mower with spark plug or carburetor down. See Figure 3.4.

3.Check torque of blade retaining cap screw. Recommended torque should be 30 to 40 ft. lbs. See Figure 3.4.

4.Check blade for sharpness, wear and damage. Refer to Section “Blade Wear Limits”.

3.2.4. CHECK ENGINE DRIVE BELT

1.Visually check engine drive belt for cracking, fraying, severed or belt strands exposed. If worn or damaged, replace belt before operating mower.

3.2.5. CHECK TRANSMISSION POLY-V BELT

1.Visually check poly-v belt for cracking, fraying, severed or belt strands exposed. If worn or damaged, replace belt before operating mower.

RECOMMENDED

BLADE RETAINING

CAP SCREW TORQUE

VALUE SHOULD BE 30

TO 40 FT. LBS.

FIGURE 3.4

3.3 SERVICE - ANNUALLY

Perform all maintenance as described in the “Service Schedule” section of this manual.

3.3.1. Engine

Service engine according to engine owner’s manual.

3.3.2. Air Filter

Refer to engine owner’s manual for service instructions.

3.3.3. Engine Oil

Refer to engine owner’s manual for service instructions.

3.4 STORAGE PROCEDURE

Refer to the Engine Owner’s Manual for directions regarding engine storage preparations. Prepare the mower for “end of season” storage as follows:

1.Drain fuel from fuel tank and let engine run until all fuel is out of the carburetor.

2.Disconnect and remove the spark plug wire away from spark plug before any other preparations are made!

3.Tape all openings closed to prevent spraying water into exhaust or air intakes during washing.

4.Tilt mower up on its rear wheels and thoroughly clean the underside of the deck. Do not tilt mower with spark plug or carburetor down. Scrape away any accumulation of grass with a putty knife and or wire brush.

5.Lubricate all exposed metal with a light coating of oil to prevent corrosion.

6.On self-propelled models, loosen wing nuts on ground speed control rod before folding handles.

7.Loosen handle knobs. Carefully fold the handles forward, “flexing” the control cables to prevent cable damage.

8.Store the mower in a shed or other dry area, protected from weather.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents European 21 Steel Deck Walk Mowers M Model Series Slope Operation Protection for ChildrenPreparation Maintenance and Storage OperationTable of Contents Introduction FamiliarizationPrimer Bulb NomenclatureStarting & Operation 2.2.1. Engine & Blade Operating InstructionsPRE-START Check List Primer Models Push & Non Commercial Self-PropelledPropelling Mower Handle Height AdjustmentStopping Cutting Height Adjustment Recycling OperationCheck Grease Level in Transmission MaintenanceService After First 5 Hours 3.2.1. Change Engine OIL On NextCheck Mower Blade Service AnnuallyStorage Procedure Check Engine Drive BeltBlade Sharpening Adjustments & RepairMower Blade Replacement 4.1.1. Standard Blade Wear Limit Ninja Blade Wear LimitWheel Drive Control Adjustment Drive Spring Repair/Replacement Driven Disc ServiceCleaning Drive Disc & Driven Disc Driven Disc AdjustmentReplacing Rubber Driven Disc Ring Driven Disc Assembly Belt Service Transmission Poly-V Belt Replacement Pulley PositionTroubleshooting Problem Probable Cause Corrective ActionMAINTENANCE/REPLACEMENT Parts Service Performed EachClean Sponge Element Engine Manual 100Decal Identification European Performance Year Limited Warranty Disclaimer of WarrantyPage European Steel Deck Walk Behind Mowers M Model Series
Related manuals
Manual 46 pages 20.32 Kb

EMRP216017B specifications

The Snapper EMRP216017B is a robust and efficient lawn mower designed for homeowners seeking a reliable solution for maintaining their lawns. Known for its exceptional performance and innovative features, this mower stands out in the competitive market of outdoor equipment.

One of the hallmark features of the Snapper EMRP216017B is its powerful engine. The mower is equipped with a dependable Briggs & Stratton engine, which is recognized for its durability and efficiency. This engine provides ample power to handle various grass types and terrains, ensuring a smooth and even cut every time.

The Snapper EMRP216017B boasts a unique rear-wheel drive system. This technology enhances maneuverability, allowing users to navigate around obstacles such as trees and flower beds with ease. The rear-wheel drive also ensures improved traction, particularly on slopes or uneven ground, making it an ideal choice for diverse landscapes.

Another significant aspect of the Snapper EMRP216017B is its Versamow System. This innovative feature allows users to mulch, bag, or discharge clippings with a simple lever adjustment. The versatility provided by this system not only promotes healthier grass growth but also saves time and effort, as homeowners can choose the best option for their lawn maintenance needs.

The mower also features a 21-inch steel mower deck, designed to provide a precise and clean cut. The durable construction of the deck ensures longevity, while its design allows for excellent airflow, which is essential for optimal clipping distribution. Furthermore, the adjustable cutting height feature gives users the flexibility to tailor the mower’s performance to their specific lawn conditions.

Comfort is another key characteristic of the Snapper EMRP216017B. The ergonomic handle is designed for user-friendly operation, reducing fatigue during extended mowing sessions. Additionally, the mower offers a convenient foldable design, making it easy to store in limited spaces.

In conclusion, the Snapper EMRP216017B is a comprehensive lawn care solution that combines power, versatility, and user comfort. Its advanced features, such as the Briggs & Stratton engine, rear-wheel drive, and Versamow System, make it an ideal choice for homeowners looking to maintain a beautiful lawn with minimal effort. Whether tackling a small yard or managing a larger landscape, this mower is engineered to deliver quality results every time.
Top Page Image Contents