Snapper 7800764 CRP218520 manual Maintenance Maintenance Introduction

Page 12

Maintenance

Maintenance - Introduction

Check Grease Level in Transmission

To retain the quality of the mower, use genuine replacement

1. Remove the transmission fill plug (A, Figure 15). Roll

the machine forward or backward while looking down

parts only. Contact a local dealer for parts and service

into the plug hole.

assistance. For the correct part or information for a

2. If liquid grease is not visible on the input gear (the small

particular mower, always mention the model and

gear below the plug hole), add an amount, to cover the

serial number.

gear, of Snapper “00” grease.

 

!

WARNING

!

A

DO NOT attempt any maintenance, adjustments or service

with engine and blade running. STOP engine and blade.

 

Disconnect spark plug wire and secure away from spark

 

plug. Engine and components are HOT. Avoid serious

 

 

burns, allow sufficient time for all components to cool.

 

 

Wear heavy leather gloves when handling or working

 

 

around cutting blades. Blades are extremely sharp and can

 

cause severe injury.

 

 

 

 

Reproduction

Service - After First 5 Hours

 

 

for

Change Engine Oil

 

 

 

 

Figure 15: Rem v ng the transmission fill plug

1. Refer to the Engine Manual for proper oil specifications,

procedures and proper service intervals.

 

 

 

 

 

Not

 

Note: Snapper “00” grease (Part No. 7029443) is available at

2. For the simplest/cleanest oil change, simply

urn he

 

mower on its side to drain the oil, as sh

wn. Drain he

 

your dealer.

oil through the dipstick tube (A, Figure 14) in

a

 

Note: Do not spill grease or oil onto the surface of the drive

container. Allow sufficient time for all the

il to drain.

 

 

 

 

 

 

isc (A, Fig re 16).

Important: Drain the fuel tank before tipping the machine.

 

 

DO NOT tip the machine with the carburetor or spark plug

 

A

down. Oil from the crankcase will saturate the air filter and

 

cause the engine to be hard to start or not start at all. If

 

 

contamination does occur, the air filter will have to be

 

 

replaced.

 

 

 

 

 

 

A

 

 

 

 

 

 

 

 

 

Figure 16: Location of the drive disc

 

 

 

 

 

3. Reinstall the transmission plug.

 

 

 

 

 

4. Check the grease level after each 25 hours of operation.

 

 

 

 

 

Important: Drain the fuel tank before tipping the mower. DO

Figure 14: Draining the engine oil

 

 

 

 

NOT tip the machine with the carburetor or spark plug down.

 

 

 

 

 

Oil from the crankcase will saturate the air filter and cause

3. Dispose of drain oil properly.

 

 

 

 

the engine to be hard to start or not start at all. If

4. Fill the engine with oil as specified in the Engine Manual.

contamination does occur, the air filter will have to be

Do not overfill.

 

 

 

 

replaced.

12

www.snapper.com

Image 12
Contents Not For 7104669 Rev. ‘-’Reproduction NotComplete the following information on your Snapper purchase Table of Contents Operator Safety Protection for Children PreparationFrom Previous Column Slope OperationMaintenance and Storage From Previous From Previous ColumnOperation Features and Controls Orf NotOperation Before Starting Operation Propelling the Mower Handle Height Adjustment Start the mowerLower handle Ground speed control Desired positionOperation Mulching Recycling Operation Removing the Mulching CoverOperation Installing the Mulching Plug Dumping the Grass BagMaintenance Maintenance Introduction Check Grease Level in TransmissionService Periodic Sto age ProcedureCheck Transmission Poly-V Belt Engine Check Mower Blade Air FilterMaintenance Mower Blade ReplacementStandard Blade Wear Limit Blade SharpeningEnd view Blade assembly To adjust, unhook the upper spring D from the cableReproduction For Cable eye C with the wheel drive control releasedDrive Spring Repair/Replacement Cleaning Drive Disc & Driven DiscIf the drive disc and driven disc are clean and the mower Reprod uctionDriven Disc Adjustment Driven Disc Ring ReplacementReprod UctionDriven Disc Bearing Replacement Driven Disc Ring ReplacementReproduction For Not Hex Shaft BeltsReplacing the Bearing On the Pulley End Transmiss on P ly-V Belt Replacement Engine Drive Belt Replacement Stretch Type BeltsDriven Disc Replacement for driven disc removal Procedure Drain the fuel tank before tipping the mower. Do not tiltService Schedule High temperaturesChange oil every 25 hours when operating under heavy l ad Troubleshooting Warranty ReproductionNot For Not For Not For Slope Guide Product Specifications Common Service Parts Part Number

7800764 CRP218520 specifications

The Snapper 7800764 CRP218520 is a top-tier lawn mower renowned for its innovative design and robust performance. This mower is part of Snapper's commitment to delivering high-quality lawn care equipment that meets the needs of both homeowners and professional landscapers.

One of the standout features of the Snapper CRP218520 is its powerful 21-inch steel cutting deck. This sturdy construction ensures durability while efficiently handling various grass types. The cutting deck is designed with a deep dome shape, allowing for superior airflow and enhancing the mower’s mulching capability. With this technology, users can achieve a finely mulched lawn, which not only looks good but also provides essential nutrients back to the soil.

The mower is equipped with a reliable 163cc OHV engine. This engine provides ample power for tackling tough mowing tasks while delivering optimal fuel efficiency. The engine’s overhead valve design contributes to reduced emissions and quieter operation, making it an eco-friendly choice for environmentally-conscious consumers.

Another notable aspect of the Snapper CRP218520 is its user-friendly features. The adjustable handle height offers comfort for users of various heights, ensuring an ergonomic mowing experience. The easy-to-utilize lever allows for quick changes in cutting height, providing versatility to adapt to varying lawn conditions. Whether dealing with tall grass or maintaining a well-manicured lawn, this mower can be adjusted quickly to suit the task at hand.

For convenience, the Snapper 7800764 features a rear bagging design, which facilitates easy grass collection for cleanup or composting. This feature is perfect for homeowners who prefer a neat and tidy yard and want to minimize the effort required for post-mowing maintenance. Additionally, the mower boasts a side-discharge capability, offering even more options for grass management.

In terms of maneuverability, the Snapper CRP218520 is designed with all-terrain wheels that enhance traction and control, making it easier to navigate around obstacles like flower beds or trees. This thoughtful engineering adds to the mower's overall efficiency and makes mowing less of a chore.

With its combination of advanced technologies, robust features, and user-focused design, the Snapper 7800764 CRP218520 is an excellent choice for those seeking a reliable and efficient lawn mower. Whether for residential or professional use, this mower promises impressive performance to keep lawns looking their best.