Snapper 421622BVE Blade Sharpening, Blade Drive Belt Replacement, Belt Removal

Page 23

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and vent must be closed securely to prevent fuel spillage.

DO NOT use a cutting blade that shows signs of excessive wear or damage on the Rear Engine Rider. On Rear Engine Riders equipped with a grass catcher attachment, the air lifts should be replaced when the blade is replaced.

IMPORTANT: If the Rear Engine Rider will be on its rear bumper for longer than two hours, remove the battery. Refer to Section “BATTERY REMOVAL”.

4.4.2. BLADE SHARPENING

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “REMOVING FUEL TANK”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

4.Remove blade. See Figure 4.12.

BLADE

CONE WASHERS

WARNING

Blades are extremely sharp and can cause severe injuries. Wear heavy leather gloves when working on or handling blades. DO NOT use blades that show signs of wear or damage.

DO NOT SHARPEN BEYOND

ORIGINAL CUTTING EDGE

22º TO 28º

BLADE TIP

ORIGINAL CUTTING EDGE

FIGURE 4.13

4.5BLADE DRIVE BELT REPLACEMENT

Inspect mower drive belt. Refer to Section “CHECK BLADE DRIVE BELT”. Replace belt if signs of excessive wear and/or damage are present.

4.5.1. BELT REMOVAL

1.Remove mower drive belt cover. Refer to Section “DRIVE BELT COVER REMOVAL”.

2.Remove old belt.

BOLT

FIGURE 4.12

5.Inspect condition of blade. See Figure 4.11.

6.If blade is in good condition, sharpen at 22 to 28 degrees. DO NOT sharpen beyond existing cutting edge. See Figure 4.13.

7.Check blade balance after sharpening. If necessary, correct blade balance by grinding the heavy end of blade.

8.Reinstall blade. See Figure 4.12. Torque blade mounting bolts to recommended range of 30 to 40 ft. lbs.

23

Image 23
Contents Manual No -4388 Rev 1, 8/27/01 Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Nomenclature IntroductionPRE-START Check List OPERATOR’S Seat Adjustment Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartEngine Manual Start Starting & OperationEngine Electric Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineDo not park the machine on slopes Cutting Height AdjustmentStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Reverse Lockout Mechanism Override Reverse Lockout MechanismChange Engine OIL Service After First 5 HoursService Engine AIR Cleaner Check Mower Blade Adjusting Mower BladeBlade Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltService Brake / Park Brake TOP View of Belt RoutingLubrication Grease Fittings Service Every 25 Operating HoursBattery Fluid Level Clean Mower DeckFuel Filter Service AnnuallyEngine Removing Fuel Tank Every TWO YearsStorage OUT of Season Blade Brake Adjustment Engine Adjustments & RepairMower Drive Belt Adjustment Side To Side Levelness Mower Deck Adjustment Front to Rear Levelness Service BRAKE/PARK Brake Adjustment Mower Blade Replacement 4.4.1. Blade Wear Limits Adjustment From PreviousBelt Removal Blade Drive Belt ReplacementBlade Sharpening Belt Replacement Battery Installation Battery Battery RemovalBattery Testing Battery ServiceBattery Storage NEW Battery Preparation 1. Remove battery from cartonSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionImproperly Loss Of TractionBlades Not Cutting Cutting GrassTo be Performed Pages Subject Service ReferenceDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Copyright 2001` Snapper INC ALL Rights Reserved
Related manuals
Manual 32 pages 21.46 Kb