Snapper 281318BE Lubrication Grease Fittings, Service Every 25 Operating Hours, Do not Overfill

Page 14

Section 3 – MAINTENANCE

3.2.8.LUBRICATION – GREASE FITTINGS

The following components on the Rear Engine Rider are equipped with grease fittings and require periodic lubrication. Apply General Purpose grease (NLGI No.2) with a grease gun.

1.Front Wheel Bearings. Refer to Section

“FRONT WHEEL BEARINGS – LUBRICATION”.

2.Rear Axle Bearing. Refer to Section “REAR

AXLE BEARING – LUBRICATION”.

3.Mower Blade Spindle. Refer to Section

“MOWER BLADE SPINDLE – LUBRICATION”.

3.3 SERVICE - EVERY 25 OPERATING HOURS

3.3.1.Perform all service required after the first 5 hours of operation. Refer to Section “SERVICE – AFTER 5 HOURS”.

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

3.3.2.BATTERY FLUID LEVEL

1.Remove battery. Refer to Section “BATTERY REMOVAL”.

2.Remove battery caps. Check fluid level.

3.Add water only to bring fluid to proper level – approximately 3/16” above plates.

DO NOT OVERFILL.

4.Reinstall battery. Refer to Section “BATTERY INSTALLATION”.

3.3.3.MOWER DECK LEVELNESS

Check mower deck for proper level. Adjust as required. Refer to Section “MOWER DECK ADJUSTMENT –

LEVELNESS”.

3.3.4.CLEAN MOWER DECK

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “REMOVING FUEL TANK”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

4.Clean underside of mower deck, removing all accumulation of grass clippings and debris.

5.Clean top of deck, removing all grass clippings and debris.

3.3.5MOWER BLADE SPINDLE - LUBRICATION

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “FUEK TANK REMOVAL”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

4.Lubricate spindle with three shots of general purpose grease from grease gun. See Figure 3.5.

IMPORTANT: If the Rear Engine Rider will be on its rear bumper for longer than two hours, remove the battery. Refer to Section “BATTERY REMOVAL”.

3.3.6.MOWER DECK LINKAGE - LUBRICATION Lubricate all mower deck linkage pivot points with a light coat of motor oil.

SPINDLE

GREASE FITTING

FIGURE 3.5

3.3.7. FRONT WHEEL BEARING - LUBRICATION

1.Lubricate front wheel bearings with five shots of general purpose grease, from grease gun. See Figure 3.6.

FRONT WHEEL

GREASE FITTING

FIGURE 3.6

14

Image 14
Contents Rear Engine Riding Mower Series Manual No -7008 REV , 8/20/99Important Safety Instructions Operation Table of Contents Nomenclature Control PanelIntroduction OPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextEngine Manual Start Starting & OperationEngine Electric Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeDo not park machine on slopes Cutting Height AdjustmentStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Change Engine OIL Service After First 5 HoursService Engine AIR Cleaner Check Mower Blade Blade Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltService Brake / Park Brake Interlock SystemClean Mower Deck Service Every 25 Operating HoursBattery Fluid Level Lubrication Grease FittingsLeft Rear Axle Bearing Grease Fitting Every TWO Years Service Annually 3.4.1. EngineFuel Filter Storage OUT of SeasonEngine Adjustments & Repair Blade Brake AdjustmentFront to Rear Levelness 30 Decks Mower Deck & Component Adjustments Mower Deck AdjustmentFront to Rear Levelness 28, & 33 Decks Wheel Brake Adjustment Brake Cable Chain Case Loosen JAM Nuts Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBelt Removal Mower Drive Belt ReplacementBelt Replacement Beltfigure 4.25 GuideBattery Battery Removal Battery InstallationNEW Battery Preparation 1. Remove battery from carton Battery ServiceBattery Storage Battery TestingSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopCutting Grass Loss Of TractionBlades Not Cutting ImproperlySubject Service Reference To be Performed PagesMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Rear Engine Riding Mower Series