Safety Decal, S E M B L Y, A R N I N G | Snapper 1691351 specification

SAFETY DECAL

I • Operate only with 540 RPM

attachmentsI

Located on PTO Shield

A S S E M B L Y

1 . Park tractor on a flat, level surface. Shut off engine, rcm”vc key. and allow all moving parts to stop.

A W A R N I N G

Iftractor has been in operation, mufiler may be hot. Use caution working around muffler or allow muffler to cool before proceeding with installation.

NOTE

The initial assembly of PTO carrier (F, figure 1) to

tract”r frame is easier with hood deck removed from tractor. To rcm”vc deck:

a. Tilt deck forward.

b. Uncouple headlight wiring harness.

c., Remove tw” spring~clips +@ two clcvis pins. d. Remove hood deck from tractor.

2.Remove PTO shield by removing spring clips and bracket. Store spring clips with bracket.

3 . Install front capscrews (i) thru carrier(F) and install washers (L), lockwasher (M), and nuts (N). Leave

hardware loose. Large washers (L),’ arc for front slotted frame holes only.

4.~ Install carrier onto tract& frame and install two rear

capscrcws (K) and hardware (M, N). Tighten snug only until PTO is installed.

5 . Apply oil or lubricant to splines of tractor PTO shaft.

6 . Remove existing bolts and nuts from PTO housing at four locations shown in figure 2. Install 5/ 16-18 x 2- 1/4 capscrews (C) from front.

7. Install spacers (G) on end of caps&s (C).

8.Install woodruff key (D) onto PTO shaft.

9.Install adaptor assembly (A) to housing input shaft.

Assembly should mwc easily “vcr shaft and key. Rotate PTO adaptor so that setscrew is at top of shaft.

10.Just start PTO adaptor assembly (A) onto tractor PTO shaft. Swivel back and forth in order to align

four capscrews (C) and spacers (G) with holes in carrier (F).

11.Install washer (H) and hex n”t (I) and tighten fully. With wrench on nut (I), install jam nut (J) and tighten snug against hex nut.

12.To make sure PTO adaptor (A) is properly aligned, lift up on PTO housing (B) with one hand while sliding adaptor back and forth. There should be 3/4” - 1” play. When adaptor slides easily between both shafts, hold PTO housing in position and tighten

four capscrews (K) securing carrier (F) to tractor frame.

13.Remove setscrew from PTO adaptor (PTO housing side) and push adaptor all the way towards tractor. When Woodruff key (D) is visible (centered) in setscrew hole, x-install setscrew and tighten.

14.Remove shipping plug from PTO housing (B) and check that gear oil is level with plug. Installvent plug

(E)when oil level is correct. Use POW gear oil as ttCCCSSUy.

REMOVAL & INSTALLATION

1.After initial assembly of PTO adaptor (A), housing

(B)and carrier (F), components should be left

a s s e m b l e d . I n s t a l l a t i o n a n d r e m o v a l c a n b e

accomplished with four capscrews (K)and mounting hardware (L, M, N).

2. Install capscrews (K) only snug initially and repeat alignment procedure (step 12).

STORAGE & LUBRICATION

1. Store PTO assembly upright on frame to prevent gear oil loss.

2.Check gear oil level every season by removing oil till

plug:on front side of PTO how&$ Oil should be level with plug opening. Do not till oil to vent plug opening. Refer to figure 1.

3.Lubricate grease fittings on each side of PTO housing (B) every 25 hours of operation. Apply only 2-3 shots of standard automotive grease.

1691351 specifications

Snapper 1691351 is an innovative outdoor power equipment solution designed to make lawn care and maintenance as efficient and effective as possible. This versatile machine is tailored for both residential and commercial users who demand reliable performance along with user-friendly features. With an emphasis on cutting-edge technology, Snapper 1691351 comes equipped with a variety of characteristics that set it apart from traditional lawn mowers.

One of the standout features of the Snapper 1691351 is its powerful engine. The mower is powered by a Briggs & Stratton engine, known for its durability and performance, providing an ideal balance of power and fuel efficiency. This not only enhances the mowing experience but also minimizes downtime, allowing users to finish their tasks quickly and efficiently.

The Snapper 1691351 boasts a Briggs & Stratton engine capable of delivering exceptional torque, ensuring a clean and even cut on all types of grass. Additionally, the mower features a 21-inch cut deck, which is perfect for getting into tight spaces while still having the capability to cover larger areas quickly. The cutting height adjustment is user-friendly, allowing for quick changes to accommodate different lawn conditions and preferences, ranging from a low trim for a golf-course look to a higher cut for a natural mow.

A major highlight of the Snapper 1691351 is its Innovatively designed Easy-Switch technology. This feature allows users to easily switch between mulching, bagging, or side-discharge modes without needing additional equipment. This flexibility not only caters to different lawn care needs but also allows for efficient management of clippings, contributing to a healthier lawn.

The Snapper 1691351 is also equipped with a robust self-propelled drive system, making it a great choice for tackling challenging terrains and inclines. The adjustable speed control allows users to tailor the mower's speed to their comfort level, resulting in an effortless mowing experience.

User comfort and safety are prioritized in the design of the Snapper 1691351. It comes with an ergonomic handle that enhances grip and reduces fatigue during prolonged use. Additionally, it features safety mechanisms like an automatic shutoff and blade brake system, ensuring that users can operate the mower with confidence.

In conclusion, Snapper 1691351 stands out due to its powerful engine, efficient cutting capabilities, easy-to-switch modes, and user-friendly design. For anyone looking for a reliable and versatile mower that can handle various lawn care tasks, the Snapper 1691351 is a worthy investment.