Snapper GT 600 Series, 2690627 Regular Maintenance, Clean Radiator, Clean Transmission Oil Cooler

Page 28

Regular Maintenance

Engine Maintenance - General

Refer to the engine owner’s manual for all engine main- tenance procedures and recommendations.

Clean Debris Out of Engine

Compartment

Service Interval: Every 25 Hours, or As Necessary

Stop the engine and allow the unit to cool. Remove all debris from the engine compartment. Be sure all cooling fins, radiators, screens, and areas around the exhaust system are clean.

WARNING

Keep the unit free of grass, leaves, and other debris. Flammable debris many be ignited by hot engine parts causing serious injury or property damage.

Clean Radiator

Service Interval: Every 25 Hours, or As Necessary

Clean the radiator, or radiator screen with compressed air at regular intervals, or if dirty. The radiator is located at the rear of the engine compartment on liquid-cooled models. Liquid cooled models also have a removable radiator screen (F, Figure 24). Clean all cooling system components.

Clean Transmission Oil Cooler

Service Interval: Every 25 Hours, or As Necessary

The transmission oil cooler (C, Figures 24) is located behind the engine and should be cleaned with com- pressed air at regular intervals or if dirty.

Check Engine Coolant Level

Service Interval: Every 25 Hours, or As Necessary

The engine coolant level and quality should be checked before each use, when the engine is off and cool.

1.Check the coolant level in the overflow reservoir (A, Figure 24). Coolant should be between the “H” and “L” marks on the tank.

2.If the coolant level is below the “L” mark on the over- flow reservoir, add coolant by shutting off the engine, allowing the engine to cool, removing the reservoir cap, and adding coolant. Proper coolant mix is a 50/50 mixture of ethylene glycol and distilled water.

Change Engine Coolant

See Engine Manual for antifreeze recommendations and change intervals. See Figures 24 for drain plug locations.

B

C

 

D

 

 

 

 

 

 

 

 

A

 

 

 

E

 

 

 

 

 

 

I

H

F

J

K

G

 

 

 

Figure 24. Engine

A.Coolant Reservoir

B.Engine Oil Fill

C.Transmission Oil Cooler

D.Radiator Fill Cap

E.Fuel Filter / Water Separator

F.Radiator Screen

G.Radiator Drain Plug

H.Oil Filter

I.Oil Dipstick

J.Air Filter

K.Oil Drain Plug (Bottom of Engine)

26

Page 27 Page 29
Image 28
Page 27 Page 29
Contents OPERATOR’S Manual 27HP Hydro Tractors & Mower DecksPage Table of Contents Safety Rules & Information Operating Safety Safety Rules and Information Slope OperationSafety Rules & Information General OperationSafety Rules and Information Service & Maintenance Safe Handling of GasolineIdentification Numbers Tractor ID TagSafety Decals Safety DecalsDecal Danger Rotating Blades Decal Danger, Rotating Fan, Diesel Models Part NoSafety Icons Operational Safety ChecksControl Functions Features & Controls Parking Brake Function Automatic Controlled TractionDashboard Display Functions General Operating Safety Slope OperationAdding Fuel Stopping The Tractor & EngineOperating the Tractor Using Inboard Hydraulics Pushing The Tractor By HandHydraulic System Functions GeneralUsing Auxiliary Hydraulics Auxiliary Hydraulics Angle Left Angle RightOptional 3-Point Hitch Operation Select Models Attachment Weight LimitLocking The Hitch Hitch Arms Installation Connecting a Drive Shaft Rear PTO Operation Select ModelsChecks Before Starting Starting & Stopping the PTOAttachment Recommendations Mower Deck Removal & Installation Removing the Mower DeckInstalling the Mower Deck Mower Electrical ConnectionAttaching a Trailer Volt Power OutletStorage Regular Maintenance Before Every Spring Each Hours Fall UseRegular Maintenance Clean RadiatorClean Transmission Oil Cooler Check Engine Coolant LevelService Interval Seasonally or as Needed Drain Fuel SeparatorService Interval Every 25 Hours Check Transmission Oil LevelCheck Front Axle Oil Level Change Transmission Oil & filterOil Filter Part No Safety Interlock System Check Service Interval Every Fall & SpringService Interval Every 100 Hours or Fall & Spring Check Mower Deck Gear Box OilBattery Maintenance Cleaning the Battery and CablesCheck Tire Pressures Size TreadGrease LubricationOil Grease the Electric Lift Rod GreaseFitting Yearly Arm Grease Fitting YearlyServicing The Mower Blades Removing the BladeMaintenance Records Troubleshooting Adjustment, & Service Troubleshooting the Mower Troubleshooting, Adjustment, & Service Seat AdjustmentBrake Adjustment Seat Slide AdjustmentTaillight & Dash Light Replacement Headlight ReplacementBattery Charging Mower Adjustments Gauge Wheel AdjustmentSide-to-Side Adjustment Lock Nut, 5/16-18 Spacer Bolt Leveling The MowerMower Drive Belt Replacement Mower Belt ReplacementTo avoid damaging belts, do not PRY Specifications 27 HP* Briggs & StrattonReplacement Parts Maintenance ItemsOptional Accessories Technical Manuals

2690627, STGT2754D, GT 600 Series specifications

The Snapper GT 600 Series, specifically the STGT2754D model, is a standout in the realm of high-performance lawn care equipment. Designed for both efficiency and durability, this mower is perfect for homeowners with medium to large lawns who seek both power and reliability in their outdoor equipment.

One of the key features of the Snapper GT 600 Series is its robust 27 horsepower engine. This powerful engine enables the mower to tackle tough terrains and thick grass effortlessly. The innovative design includes a cutting deck size of 54 inches, which allows for a wide cutting path that reduces mowing time and enhances productivity. The adjustable cutting height provides multiple settings, accommodating various grass types and preferences, from a low, manicured look to a higher cut for more rugged areas.

The Snapper GT 600 Series incorporates advanced engineering with its high-performance transmission system. This system provides smooth acceleration and effortless steering, ensuring that maneuvering around obstacles like trees and flower beds is a breeze. The quick-turn radius enhances this maneuverability, allowing the operator to navigate tight spaces with confidence.

Technology plays a significant role in the GT 600 Series. The mower boasts an intuitive dashboard equipped with user-friendly controls, including easy-to-read displays for speed and fuel level. This feature not only enhances user experience but also promotes efficiency by allowing the operator to monitor essential metrics in real time.

Another notable characteristic of the STGT2754D is its durability. Built with a robust steel frame and heavy-duty components, this mower is designed to withstand the rigors of regular use. The weather-resistant materials ensure longevity and reliability under various conditions, making it a wise investment for any lawn care enthusiast.

Moreover, the Snapper GT 600 Series prioritizes user comfort. The high-back seat is designed for extended use, providing ample support and reducing fatigue during longer mowing sessions. Additionally, the vibration dampening system minimizes discomfort, enhancing overall control and driving experience.

In conclusion, the Snapper GT 600 Series STGT2754D is a powerful, technologically advanced lawn mower designed for efficiency and ease of use. Its combination of a robust engine, wide cutting deck, advanced transmission system, and user-friendly features make it a top choice for homeowners seeking to achieve a pristine lawn with minimal effort. Whether you're a seasoned gardener or a novice, the Snapper GT 600 Series promises to deliver performance and reliability for all your lawn care needs.
Top Page Image Contents