Snapper 2167519B, P2167519B, P217019BV, P217019BVE, P216019KWV Operating Instructions, 10a

Page 9
2.6 INSTALLATION of GRASS BAG ADAPTER

Section 2 - OPERATING INSTRUCTIONS

2.Set all wheels at the same cutting height. The highest cutting position is Notch 7. The lowest cutting position is Notch 1. See Figures 2.8 & 2.9.

LATCH

POSITION

CUTTING HEIGHT SETTINGS

FIGURE 2.9

2.6 INSTALLATION of GRASS BAG ADAPTER

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

STEP 1: Install the grass bag adapter and secure to the side and top of the deck with the two nuts provided on the machine. Slot in front edge of adapter must be under nut located on top of deck. See Figure 2.10.

SECURE ADAPTER

TO DECK WITH NUTS

STEP 1a (Kawasaki only): Attach Bag Adapter Standoff between rope guide pulley assembly and engine recoil. See Figure 2.10a.

A. Remove right rear bolt from engine recoil cover. B. Remove torx screw and nut securing rope guide pulley to bracket on bag adapter.

C. Lay standoff between bolt holes in engine recoil cover and bag adapter pulley bracket. NOTE: position standoff so that bent end is toward engine recoil cover.

D. Flip pulley over so that flange of steel bushing is under pulley. (The bushing will act as a washer between the pulley and standoff.)

E. Reassemble pulley to bag adapter, and install supplied replacement bolt, fitted with thread sleeve, into recoil cover. Tighten all hardware securely.

REPLACEMENT

BOLT WITHSTANDOFF

THREAD SLEEVE

ROPE GUIDE PULLEY

BEND

FIGURE 2.10a RECOIL ROPE

FIGURE 2.10a

STEP 2: Route recoil rope around recoil rope pulley on

bag adapter. See Figure 2.10a. NOTE: Pulling Blade control against upper handle will allow extra recoil slack.

2.7INSTALLATION of RECYCLING PLUG (Optional Accessory on Some Models)

STEP 1: Once adapter has been installed, recycling may be desired. Insert recycling plug completely and securely into adapter. See Figure 2.11. Install grass bag as a safeguard.

INSERT RECYCLING PLUG

PLUGCOMPLETELY AND SECURELY INTO ADAPTER. INSTALL GRASS BAG.

ADAPTER

SECURE

WITH NUTS

ADAPTER

FIGURE 2.10

FIGURE 2.11

STEP 2: Refer to Section “OPERATING

INSTRUCTIONS – RECYCLING OPERATION”.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents 21” STEEL DECK WALK MOWERS SERIES Safety Instructions & Operator’s Manual forMODELS 2167519B P2167519B P217019BV P217019BVE P216019KWVPROTECTION FOR CHILDREN IMPORTANT SAFETY INSTRUCTIONSSLOPE OPERATION PREPARATIONOPERATION MAINTENANCE AND STORAGEMAINTENANCE AND STORAGE TABLE OF CONTENTS BRIGGS Section 1 - FAMILIARIZATIONENGINE SPEEDSection 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECK LIST2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE Briggs Engine 2.5 CUTTING HEIGHT ADJUSTMENT 2.4 HANDLE HEIGHT ADJUSTMENT2.2 STARTING & OPERATION 2.2.1. ENGINE & BLADE Kawasaki Engine 2.3 STOPPING2.6 INSTALLATION of GRASS BAG ADAPTER 2.7 INSTALLATION of RECYCLING PLUG Optional Accessory on Some ModelsFIGURE 2.10a Attach grass bag hooks over middle handle cross bar See Figure 1. Set all wheels in the highest cutting position Notch Section 3 - MAINTENANCE 3.2.3. CHECK MOWER BLADE Section 4 - REPAIR & ADJUSTMENTS 4. Sharpen blade on a grinding wheel at an angle of 1. Grease on drive disc causing slippage 7. Reinstall driven disc spring to driven disc assembly Section 4 - REPAIR & ADJUSTMENTS To replace the bearing on the pulley end of the hex Remove the driven disc. Refer to Section Methods of Checking Battery Condition PROBLEM TROUBLESHOOTINGPROBABLE CAUSE CORRECTIVE ACTIONMAINTENANCE PARTS SERVICE SCHEDULE2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SNAPPER PRODUCT REGISTRATION FORM Page Page 21” STEEL DECK WALK BEHIND MOWERS SERIES
Top Page Image Contents