Snapper E281318BE, E331518KVE Blade Drive Belt Replacement, Belt Removal

Page 24

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and vent must be closed securely to prevent fuel spillage.

4.5BLADE DRIVE BELT REPLACEMENT

Inspect mower drive belt as described in Section “CHECK MOWER DRIVE BELT”. Replace belt if signs of excessive wear and/or damage are present.

4.5.1. BELT REMOVAL

1.Remove mower drive belt cover. Refer to Section “Drive Belt Cover Removal”.

2.Remove old belt.

4.5.2. BELT REPLACEMENT

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “REMOVING FUEL TANK”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

4.Route new belt through engine belt guide up to engine pulley.

ENGINE

PULLEY

ENGINE

BELT

GUIDE

FIGURE 4.12

5.Move transmission shift lever to the neutral (N) position.

6.Rotate clutch yoke out with your hand and work belt between drive disc and rubber driven disc.

7.To clear the primary chain case, move transmission shift lever to the #5 position. Route belt around drive disc and into drive pulley belt groove. See Figure 4.12.

8.Remove fixed idler. Make sure belt is inside belt guide and idler. See Figure 4.13.

9.Route belt onto spindle pulley. Make sure belt is inside belt guide. See Figure 4.14.

10.Reinstall fixed idler removed in Step 8. Tighten idler pulley bolt securely.

BELT MUST BE TO THE INSIDE OF BELT GUIDE

BELT

GUIDE

FIXED

IDLER

PULLEY

FIGURE 4.13

11.Adjust belt guide. See Figure 4.14 for proper belt-to-belt guide clearances.

12.Reinstall mower drive belt cover.

28”, 30”, & 33” MODELS (DUAL IDLER SYSTEM)

1/16” NOMINAL

FIGURE 4.14

24

Image 24
Contents European Rear Engine Riding Mower Series Manual No -7007 REV , 8/20/99Important Safety Instructions Operation Table of Contents Introduction NomenclatureFamiliarization Decals / Symbols Blade Engaged Position Safety Instruction OPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextStarting & Operation Engine Electric StartEngine Manual Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeCutting Height Adjustment Stopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park BrakeDo not park the machine on slopes Service After First 5 Hours Service Engine AIR Cleaner Check Mower BladeChange Engine OIL Service After First 5 Hours 3.2.4. Check Blade Drive Belt Service Brake / Park BrakeBlade Brake Interlock SystemService Every 25 Operating Hours Battery Fluid LevelClean Mower Deck Lubrication Grease FittingsLeft Rear Axle Bearing Grease Fitting Service Annually Fuel FilterEvery TWO Years Storage OUT of SeasonEngine Adjustments & Repair Blade Brake AdjustmentMower Deck Adjustment Front to Rear Levelness 28, & 33 DecksFront to Rear Levelness 30 Decks Adjustments & Repair Wheel Brake AdjustmentChain Case Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBlade Drive Belt Replacement Belt ReplacementBelt Removal Battery Battery Removal Battery InstallationBattery Service Battery StorageBattery Testing NEW Battery Preparation 1. Remove battery from cartonSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopLoss Of Traction Blades Not CuttingCutting Grass ImproperlySubject Service Reference Power LWATo be Performed Pages Vibration Max Less ThanMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyService Notes Service Notes Service Notes European Rear Engine Riding Mower Series