Snapper E281318BE, E331518KVE Starting & Operation Engine Electric Start, On Next

Page 9

Section 2 - OPERATING INSTRUCTIONS

2.3 STARTING & OPERATION

2.3.1. ENGINE (ELECTRIC START)

IMPORTANT: When the ignition key is turned to “START”, the engine will turn over, but willnot start unless the Clutch/Brake pedal is pressed all the way down, the Blade Lever is in the “Off” position (See Figure 2.5).The operator should be in the seat. Start engine as follows:

1.Move transmission shift lever to (N) Neutral position. DO NOT start engine with transmission shift lever in a drive position.

WARNING

It is possible to start engine with transmission shift lever in a drive position. Follow starting instructions carefully.

2.Make certain the Blade Lever is in the “Off” position. See Figure 2.4.

BLADE LEVER

IN “OFF”

POSITION

RELEASE BLADE

PEDALS

FIGURE 2.4

3.Press Clutch/Brake Pedal all the way down and hold while starting engine. See Figure 2.5.

4.Open vent on fuel filler cap by turning counterclockwise. IMPORTANT: Failure to open vent on the fuel filler cap can cause engine to stall. See Figure 2.6.

5.Move engine speed control to the choke position to start a cold engine. See Figure 2.7.

6.Turn key to the “START” position until engine starts. See Figure 2.7. NOTE: If after 5 seconds of cranking the engine and it does not start, release the key, make sure the Clutch/Brake Pedal is fully depressed and attempt starting again after waiting for approximately 20 seconds.

7.After engine starts, move engine speed control to the “FAST” position, allow a brief warm-up until engine runs smooth.

TO APPLY

BRAKES, PUSH

CLUTCH/BRAKE

PEDAL ALL THE

WAY DOWN

FIGURE 2.5

FUEL

OPEN

VENT

FILLER

 

CAP

 

FUEL

 

TANK

 

FIGURE 2.6

KEY

MOVE ENGINE SPEED

CONTROL TO CHOKE

POSITION

FIGURE 2.7 (Continued on Next Page)

9

Image 9
Contents Manual No -7007 REV , 8/20/99 European Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Nomenclature IntroductionFamiliarization Decals / Symbols Blade Engaged Position Safety Instruction PRE-START Check List OPERATOR’S Seat Adjustment 2.2.1. Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartStarting & Operation Engine Electric StartEngine Manual Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineCutting Height Adjustment Stopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park BrakeDo not park the machine on slopes Service After First 5 Hours Service Engine AIR Cleaner Check Mower BladeChange Engine OIL Service Brake / Park Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltBlade Brake Interlock SystemBattery Fluid Level Service Every 25 Operating HoursClean Mower Deck Lubrication Grease FittingsLeft Rear Axle Bearing Grease Fitting Fuel Filter Service AnnuallyEvery TWO Years Storage OUT of SeasonBlade Brake Adjustment Engine Adjustments & RepairMower Deck Adjustment Front to Rear Levelness 28, & 33 DecksFront to Rear Levelness 30 Decks Wheel Brake Adjustment Adjustments & RepairChain Case Blade Sharpening Mower Blade Replacement 4.4.1. Blade Wear LimitsBlade Drive Belt Replacement Belt ReplacementBelt Removal Battery Installation Battery Battery RemovalBattery Storage Battery ServiceBattery Testing NEW Battery Preparation 1. Remove battery from cartonSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionBlades Not Cutting Loss Of TractionCutting Grass ImproperlyPower LWA Subject Service ReferenceTo be Performed Pages Vibration Max Less ThanMAINTENANCE/REPLACEMENT Parts Maintenance Parts Disclaimer of Warranty Year Limited WarrantyService Notes Service Notes Service Notes European Rear Engine Riding Mower Series