Snapper EP2167517BV important safety instructions Wheel Drive Control Adjustment

Page 12

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.Sharpen blade on a grinding wheel at an angle of

22to 28 degrees. DO NOT sharpen blade beyond original cutting edge. See Figure 4.4.

DO NOT SHARPEN

BEYOND ORIGINAL

CUTTING EDGE

22-28º

BLADE TIP

END VIEW OF

BLADE ASSEMBLY

ORIGINAL CUTTING EDGE

FIGURE 4.4

5.Check blade for balance. If necessary, correct balance by grinding heavy end of blade.

6.Reinstall blade. See Figure 4.1. Check torque of blade retaining cap screw. Recommended torque should be 40 ft. lbs.

4.2WHEEL DRIVE CONTROL ADJUSTMENT

1.The wheel drive control is properly adjusted when there is 1/16” to 1/8” clearance between the inside of the spring hook and the inside of the clutch cable eye with the wheel drive control released. See Figure 4.5.

CLUTCH CABLE

 

VINYL SPRING COVER

 

1/16” TO 1/8”

CLUTCH CABLE

CLEARANCE

EYE

UPPER

 

SPRING

SPRING HOOK

 

LOWER

 

SPRING

 

CABLE

CLUTCH CABLE EYE

SPRING

FIGURE 4.5

2.To adjust, unhook upper spring from cable eye and rotate spring in direction required to extend or shorten spring length.

3.Rehook upper spring to cable eye and check clearance. Repeat procedure if required.

NOTE: The vinyl spring cover should be kept over the spring at all times except for adjustments.

4.If the wheel drive control fails to return quickly to the “OFF” position when released, check for binding at the cable holdings located on the side of the right handle. The upper clip should be located 2” below the upper knob; the lower clip should be 4” above the lower knob. The cable should slide freely with the clips installed at these locations.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents European 21 Steel Deck Walk Mowers Series Model Number ExplanationProtection for Children Slope OperationPreparation Maintenance and Storage OperationTable of Contents Familiarization Introduction NomenclatureOperating Instructions PRE-START Check ListStarting & Operation 2.2.1. Engine & Blade Primer Models Cutting Height Adjustment Handle Height AdjustmentPropelling Mower Self Propelled Models OnlyInstallation of Grass Catcher Maintenance Service After First 5 HoursIntroduction Check Grease Level in Transmission Change Engine OILService Annually Storage ProcedureCheck Mower Blade Check Engine Drive BeltRepair & Adjustments Mower Blade Replacement 4.1.1. Standard Blade Wear LimitBlade Sharpening 1.A. Ninja Blade Wear LimitWheel Drive Control Adjustment Driven and Drive Disc Service Driven Disc AdjustmentCleaning Drive Disc & Driven Disc Drive Spring Repair/ReplacementReplacing Rubber Driven Disc Drive Disc Assembly Install NEW Driven Disc Snap Rings Belt Service Pulley Position Troubleshooting Problem Probable Cause Corrective ActionService Performed Each Clean Sponge Element Engine ManualMAINTENANCE/REPLACEMENT Parts 100Decal Identification European Performance Year Limited Warranty Disclaimer of WarrantyPage European Steel Deck Walk Behind Mowers Series

EP2167517BV specifications

The Snapper EP2167517BV is a versatile and reliable lawn mower engineered to tackle various yard sizes with ease. Designed for both homeowners and landscaping professionals, it combines cutting-edge technology with user-friendly features, making it a popular choice among lawn care enthusiasts.

One of the standout features of the Snapper EP2167517BV is its robust 21-inch steel cutting deck. This durable construction provides excellent cutting capability and longevity, ensuring that users can maintain a well-manicured lawn season after season. The mower is equipped with a powerful 163cc engine that delivers ample power for efficient cutting and maneuvering across various terrains. The engine promotes fuel efficiency, enabling longer run times between refueling.

The EP2167517BV features a 3-in-1 cutting system, allowing users to choose between mulching, bagging, or side discharge options. This flexibility enables optimal grass management according to specific yard needs and preferences. The adjustable cutting height, with several positions available, makes it convenient to achieve the desired grass length quickly.

Another notable feature is its innovative self-propelled drive system, which significantly reduces the effort needed to push the mower. This is especially beneficial for larger lawns or slopes, as it allows for smoother navigation without straining the user. The ergonomic handle is designed for comfort and control, making it easy to maneuver the mower around obstacles.

In terms of technology, the Snapper EP2167517BV boasts maintenance-friendly features, such as easy access to the air filter and oil fill. The quick-release folding handlebar simplifies storage, ensuring that the mower occupies minimal space when not in use.

Furthermore, the Snapper brand is known for its commitment to quality and reliability, and the EP2167517BV is no exception. With a reputation for durability, this lawn mower is built to withstand the rigors of regular use, making it an excellent investment for homeowners seeking to enhance their lawn care routine.

In summary, the Snapper EP2167517BV combines a powerful engine, versatile cutting options, user-friendly design, and durable construction into one impressive lawn mowing solution. Its innovative features and dependable performance make it a top choice for maintaining a healthy and attractive lawn.
Top Page Image Contents