Snapper SPE150KH, SPE1250KW Mower Attachment Service, Transmission Belt REMOVAL/REPLACEMENT

Page 22

SECTION 7 - MOWER ATTACHMENT SERVICE

7.1 TRANSMISSION BELT

REMOVAL/REPLACEMENT

4, Adjust Traction Rod and Brake Rod as necessary.

Refer to Section "ADJUSTMENTS

STEERING/BRAKES and TRACTION LEVERS/RODS".

WARNING

DO NOT attempt any maintenance, adjustments or service with the engine running. Stop engine. Stop

blades. Lock Traction Levers. Remove key. Disconnect spark plug wires from spark plugs and secure wires away from spark plugs. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine.

1.Disconnect idler arm spring.

2, Remove existing belt. Replace with new belt, part no. 2-9118.

3.Reconnect idler arm spring. See Figure 7.1.

TRANSMISSION

IDLER BELT

 

IDLER ARM

ELECTRIC

SPRING

CLUTCH

 

o

FIGURE 7.1

7,2 TRACTION BELT REMOVAL &

REPLACEMENT

7.2,1. TRACTION BELT REMOVAL

1.STOP ENGINE! Remove two wing-nuts retaining belt cover. Remove belt cover. See Figure 7.2.

2.Remove Traction Belt from Wheel Pulley first by running Belt off as Wheel is turned. Remove belt from Transmission output Pulley next.

3.Lay Traction Belt flat on ground (around tire) and roll

Mower Wheel over Traction Belt, removing Traction Belt from machine,

TRACTION BELT

OUTPUT PULLEY

(WHEEL PULLEY

/

NOT SHOWN)

 

BELT COVER

WING NUT

FIGURE 7.2

 

7,3 CUTTER DECK BELT REMOVAL &

INSTALLATION

1.Remove mower deck belt cover.

2, Remove idler spring and swing idler away from belt. See Figure 7.3.

3.Remove old belt from spindle pulleys and electric clutch pulley.

4.Route new belt, part number 3-5710 for 36" Deck &

2-9261 for 48" Deck around spindle pulleys. NOTE: 36" Deck Belt also connects to electric clutch.

5.Move idler to belt and re-attach tension spring.

6.For 48" Deck to electric clutch use belt 2-9262.

36" DECK SHOWN

REMOVE

IDLER

BELT

 

7.2,2, TRACTION BELT INSTALLATION

1.STOP ENGINE! Lay new Traction Belt, part number 4-6240, flat on ground in front of Traction Wheel. Roll Traction Wheel over Traction Belt until wheel is in middle of belt.

2,

Place Traction

Belt

on Wheel

Pulley followed by

FIGURE 7.3

 

 

Transmission

Output

Pulley.

 

 

3.

Reinstall belt cover and tighten

two wing-nuts.

 

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model Designation Model Type Model Option Model Number ExplanationEngine Type Series Designation Engine HP Protection for Children Important Safety InstructionsPreparation Slope OperationMaintenance OperationImportant Safety Instructions Contents Familiarization IntroductionSafety Messages and Symbols Keep Children and Others OUT of the Mowing AreaImportant Safety and Operating Instructions Controls Traction Lever Locked PositionBefore Operating Operating InstructionsStopping Machine PRE-START Check List Starting & Operating Engine Start Engine AS FollowsStarting & Operating From previousReverse Operation To Reverse Direction Mowing and Turning on Adjusting Caster Wheels Adjusting Blade on CutterCutting Height Adjustment SpindleAdjusting Fixed Deck Attachment Side Profile of UnitSection Troubleshooting Symptom Problem Solution TroubleshootingHours Procedure Comments Traction LEVERS/RODS AdjustmentsSTEERING/BRAKES RotateTransmission Shift Lever Adjustment Handle HeightTransmission Parts & Service Power Unit ServiceReplacement Parts 2, Transmission 3. Transmission LubeTransmission Belt REMOVAL/REPLACEMENT Mower Attachment ServiceTraction Belt Removal Cutting Blade Service Standard Replacement BladesToveblabe Kawasaki ElectricalEngine only OPC Year Limited Warranty Disclaimer of WarrantyHow Quickly ruin an engine, manufacturers equip their 10, Cost YOU MoneyEngine Check OIL Level Before Each START-UPTorq Starting Check ListPage Page PRO Gear Express MID-SIZE Walk Behind Mowers Series
Top Page Image Contents