Snapper SPE152KW, SPE132KW, SPE361, SPE481 PRE-START Check List, Starting & Operating

Page 11

SECTION 3 - OPERATING INSTRUCTIONS

3.4 PRE-START CHECK LIST

Make the following checks and perform the services as required before each start-up:

1.If required, make cutting height adjustments. Refer to Section “CUTTING HEIGHT ADJUSTMENT”.

2.Check tires and add air as needed to bring pressure to 25 psi in front and 12-15 psi in rear tires.

3.Check Guards, Deflector, and Belt Covers to make sure all are in place and secure.

4.Check Condition of Cutter Deck Belt(s). If dam- aged, replace before operating machine. Refer to Section “CUTTER DECK BELT REMOVAL”.

5.Clean Interior and Exterior Surfaces of cutting deck and clean Engine of any accumulation of dirt, grass, oil, etc. Keep Engine air intake screens and cooling fins clear at all times.

6.Check Engine Oil and add oil as needed to bring level up to (but not over) the FULL mark. (Refer to Engine manual for oil specifications).

7.Add Fuel to tank after pushing the Mower outside where fumes can be dissipated. Make sure Fuel Tank Cap is tightened after refueling. (Refer to Engine manual for fuel specifications).

NOTE: DO NOT add fuel while engine is running or hot. Use fresh, clean, lead-free gasoline. DO NOT use gasoline that has been stored for long periods. Leaded gasoline or gasohol is NOT recommended.

3. Place Transmission Shift Lever in NEUTRAL(N) position. See Figure 3.3.

TRANSMISSION

SHIFT LEVER

FIGURE 3.3

4.Pull Blade Clutch Switch rearward to the OFF position. See Figure 3.4.

3.5 STARTING & OPERATING

3.5.1. ENGINE: START ENGINE AS FOLLOWS:

1.Turn Fuel Shut-Off Valve ON. See Figure 3.2.

2.Squeeze both Traction Levers toward the Handle while pulling right and left Traction Locks rearward until BOTH Traction Levers are LOCKED in the Traction Locked position. See Figure 3.2.

RIGHT HAND

TRACTION

LEVER

TRACTION LOCK

SHOWN IN TRACTION

LOCKED POSITION

FUEL SHUT OFF VALVE SHOWN IN CLOSED POSITION (ROTATE HANDLE 90 DEGREES TO OPEN)

FIGURE 3.2

BLADE

CLUTCH

SWITCH

SHOWN IN

OFF POSITION

FIGURE 3.4

(Continued on next page)

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model Number Explanation PRO Gear Express Walk Behind Mowers MID-SIZE SeriesPreparation Important Safety InstructionsProtection for Children Slope OperationOperation Safe Handling of GasolineMaintenance Table of Contents Nomenclature FamiliarizationIntroduction Keep Children and Others OUT of the Mowing Area Safety Messages and SymbolsImportant Safety and Operating Instructions Controls Stopping Machine Safety Interlock System ChecksOperating Instructions Before OperatingEngine Start Engine AS Follows PRE-START Check ListStarting & Operating On next To Reverse Direction Reverse OperationStopping Machine Mowing and Turning on Hillsides Traction Lock OperationTurning Mower Adjusting Blade on Cutter Spindle Cutting Height AdjustmentAdjusting Caster Wheels Side Profile of Unit Adjusting Fixed Deck AttachmentSymptom Problem Solution TroubleshootingHours Procedure Comments Mower TroubleshootingTraction LEVERS/RODS AdjustmentsSTEERING/BRAKES Handle Height Transmission Shift Lever AdjustmentTransmission Parts & Service Power Unit ServiceReplacement Parts Cutter Deck Belt Removal & Installation Mower Attachment ServiceTransmission Belt REMOVAL/REPLACEMENT Traction Belt Removal & ReplacementBlade Removal and Sharpening Cutting Blade ServiceStandard Replacement Blades Remove spindle pulley from spindle shaft Kawasaki Engine only ElectricalElectric Clutch Yellow Black Blue Engine 15A Fuse Disclaimer of Warranty Year Limited WarrantySnapper Product Registration Form Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page PRO Gear Express MID-SIZE Walk Behind Mowers Series
Top Page Image Contents