Snapper SPE132KW, SPE152KW, SPE361, SPE481 Remove spindle pulley from spindle shaft

Page 24

SECTION 7 - MOWER ATTACHMENT SERVICE

7.5 MOWER SPINDLES (Field Serviceable Spindles) BEARING REPLACEMENT

In the event that a spindle bearing requires replacement, the SNAPPER Field Serviceable Spindles have been designed so that no special tools or presses are required.

IMPORTANT: Spindle housing must be filled with grease before operating mower. Failure to fill housing will cause premature bearing failure.

1.Remove belt. Loosen blade nut and remove. Allow blade bolt, washer, blade and four spacers to drop down out of the spindle housing. See Figure 7.7.

REMOVE NUT

REMOVE BELT

FROM SPINDLE

REMOVE BLADE

BOLT

FIGURE 7.7

2.

Remove spindle pulley from spindle shaft.

3.

Locate circular retaining ring on spindle shaft at

top bearing. Remove retaining ring. Allow spindle

shaft to drop out of housing.

4.

Top and bottom bearings are now removable.

Pull out on inner race to slide bearing from

housing. See Figure 7.8.

5.

Thoroughly clean all parts removing all old

contaminated grease.

6.

Install new bottom bearing first.

7.

NOTE: The bearing is sealed/shielded on one

side only. The bottom bearing must be installed

with the sealed/shielded side DOWN.

8.

Insert spindle shaft up through the bottom

BEARING

SEAL UP

BEARING SEAL DOWN

PULLEY

SPACER

NYLOS SEAL

RETAINING RING

BEARING

SPINDLE

HOUSING

SPACER

BEARING

SPINDLE SHAFT

bearing. Slide spacer down over spindle shaft.

9. Install new top bearing. Install the top bearing

with the seal/shield UP.

10.

Slide circular retaining ring down spindle shaft

until it fully locks into groove on shaft.

11.

Apply a generous amount of general-purpose

grease to the concave side of the nylos seal.

Install the nylos seal with concave greased side

down.

12.

Place spindle pulley and spacer on top of

spindle shaft.

13.

Reinstall blade bolt, washer, blade and four

spacers. See Figure 7.6.

14.

Torque blade bolt and nut to 70 to 80 ft. lbs.

15.

Pump grease into spindle housing until grease

purges from vent on housing.

16.

After the first 5 hours of operation, grease

spindle housing to insure it is full, then every 25

hours.

FIGURE 7.8

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PRO Gear Express Walk Behind Mowers MID-SIZE Series Model Number ExplanationImportant Safety Instructions Protection for ChildrenSlope Operation PreparationSafe Handling of Gasoline OperationMaintenance Table of Contents Familiarization IntroductionNomenclature Safety Messages and Symbols Keep Children and Others OUT of the Mowing AreaImportant Safety and Operating Instructions Controls Safety Interlock System Checks Operating InstructionsBefore Operating Stopping MachinePRE-START Check List Starting & OperatingEngine Start Engine AS Follows On next Reverse Operation Stopping MachineTo Reverse Direction Traction Lock Operation Turning MowerMowing and Turning on Hillsides Cutting Height Adjustment Adjusting Caster WheelsAdjusting Blade on Cutter Spindle Adjusting Fixed Deck Attachment Side Profile of UnitTroubleshooting Symptom Problem SolutionMower Troubleshooting Hours Procedure CommentsAdjustments STEERING/BRAKESTraction LEVERS/RODS Transmission Shift Lever Adjustment Handle HeightPower Unit Service Replacement PartsTransmission Parts & Service Mower Attachment Service Transmission Belt REMOVAL/REPLACEMENTTraction Belt Removal & Replacement Cutter Deck Belt Removal & InstallationCutting Blade Service Standard Replacement BladesBlade Removal and Sharpening Remove spindle pulley from spindle shaft Electrical Kawasaki Engine onlyElectric Clutch Yellow Black Blue Engine 15A Fuse Year Limited Warranty Disclaimer of WarrantySnapper Product Registration Form Primary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page PRO Gear Express MID-SIZE Walk Behind Mowers Series
Top Page Image Contents