Snapper S22675, SP22675, SPV22675HW, NS22675, NSP22675, NSPV22675HW specifications Blade Service

Page 17

Maintenance (Continued)

Blade Service

WARNING: Before you inspect the blade or the blade adapter, disconnect the wire to the spark plug. If the blade hits an object, stop the engine. Disconnect the wire to the spark plug. Check the unit for damage.

Frequently check the blade for wear or damage such as cracks. Frequently check the bolt that holds the blade. Keep the bolt tight. If the blade hits an object, stop the engine. Disconnect the wire to the spark plug. Check the blade adapter (A, Figure 24) for damage. Check for a bent or damaged blade, a badly worn blade, or other damage. Before you operate the unit, damaged parts must be replaced with factory replacement parts. For safety, replace the blade every two years. Keep a sharp edge on the blade. A blade that is not sharp will cause the ends of the grass to become brown. Remove the blade as follows.

Removing the Blade

WARNING: Before you remove the blade, disconnect the wire to the spark plug. The blade has sharp edges. When you hold the blade, use gloves or cloth material to protect your hands.

1.Drain the fuel tank.

2.Lift the side of the mower that has the muffler or spark plug.

3.Use a piece of wood to keep the blade from rotating.

4.Remove the bolt (B, Figure 24) that holds the blade with a 9/16” (14mm) wrench.

5.Check the blade (C) according to the “Blade Service” instructions. Replace a badly worn or damaged blade with a factory replacement blade.

6.Mount the blade with the curved edges toward the housing. If the blade is upside down, the blade will not cut correctly and can cause an accident.

7.Fasten the blade with the original washer (D) and bolt. Make sure the outside rim of the Belleville washer is toward the blade.

8.Tighten the bolt that holds the blade to a torque of 30 foot pounds.

WARNING: Always keep the bolt that holds the blade tight. A loose bolt or blade can cause an accident.

A

C

D

A

B

 

C

D

B

 

Figure 24: Removing the blade

Sharpening the Blade

WARNING: Vibration is the result if the blade is not correctly balanced. A blade that is damaged with cracks can break and cause an accident.

1.Sharpen the blade two times a year or every 25 hours.

2.If the blade is on the unit, do not sharpen. Remove the blade according to the instructions in “Removing The Blade”.

3.Clean the blade with a brush, soap, and water. Check the blade. Look for cracks, nicks, or other damage. Replace a blade that is badly worn, bent, or damaged with a factory replacement blade.

4.Sharpen the blade (A, Figure 25, next page) with a file

(B). Make sure you keep the original beveled cutting edge.

5.Make sure the blade is balanced. Use a screwdriver (C) and hold the blade parallel to the ground (D) as shown. A blade that is balanced will stay parallel to the ground. If the blade is not balanced, the heavy end will rotate toward the ground. Sharpen the heavy end until the blade is balanced.

6.A new blade will cut better than a badly worn blade. Every two years replace the old blade with a factory replacement blade.

Checking the Level of Cut

Test the unit in a small area. If the height of cut is not level or if the cut grass is not discharged, the cause can be: (1) the blade is bent or damaged, (2) the blade is not sharp, (3) a worn blade, (4) or a broken blade adapter. Before you use the unit, correct the problem.

Maintenance

15

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Walk Behind Mowers Engine Date of Purchase Retailer Retailers Phone Number EquipmentTable of Contents Slope Operation Protection for ChildrenPreparation Preparation From Previous ColumnSafe Handling of Gasoline From Previous Maintenance and StorageOperation Operation From Previous ColumnHandle PreparationUnpacking Handle Height Adjusting the handle heightAssembling the Grass Bag Installing the frame assemblyEmptying the Grass Bag Mounting the Grass BagAttaching the Side Mounted Discharge Deflector Final Preparation Mulching TipsPreparing the Engine Engine Stop Lever OperationFront Wheel Drive System Self-Propelled Units Only Stopping the EngineRules for Safe and Effective Operation Starting the EngineEngine Maintenance MaintenanceCleaning the Mower Housing Engine TippingRemoving the belt cover Removing the Drive Belt Self-Propelled Units OnlyAdjusting the drive cable Adjusting the Drive Cable Self-Propelled Units OnlyRemoving the Blade Blade ServiceSharpening the Blade Checking the Level of CutSharpening the blade Preparing the Mower for StorageTroubleshooting Year Limited Warranty Slope Guide Page Page Common Service Parts Product Specifications

SP2265, S2265, SPV22675HW, NS2265, NSPV22675HW, S22675, SP22675, SPV22675HW, NS22675, NSP22675, NSPV22675HW specifications

The Snapper S22675, SP22675, and their variants like SPV22675HW, NS22675, NSP22675, NSPV22675HW, SP2265, S2265, SPV22675HW, NS2265, and NSPV22675HW represent a significant range of power equipment designed for lawn maintenance and landscaping. These models are particularly popular for their performance, durability, and user-friendly features tailored for both amateur gardeners and professional landscapers.

One of the key features of the Snapper S22675 series is its powerful engine. Designed for efficiency, these mowers often come equipped with high-performance Briggs & Stratton engines, ensuring robust power output while maintaining fuel economy. This makes them ideal for cutting through thick grass and tackling various terrain types with ease.

Another standout characteristic is the engineering of the cutting deck. The cutting decks in Snapper mowers are constructed for optimal airflow, which enhances grass clipping distribution and ensures a clean finish. Users can expect an even cut thanks to the innovative design that minimizes clumping, a common issue when mowing wet or lush grass.

The Snapper lineup also emphasizes user convenience. Models like the SP22675 and SPV22675HW often include self-propulsion features that allow for easy maneuverability across large lawns, reducing the physical effort required by the operator. The variable speed transmission system enables users to adjust the speed to their walking pace, making it adaptable for various user preferences and conditions.

Additionally, several models in the Snapper S22675 series feature adjustable cutting heights. This allows users to customize their mowing experience based on seasonal grass growth or specific lawn care requirements. The adjustment mechanism is designed for quick changes, enabling users to optimize their cut effortlessly.

Durability is yet another hallmark of the Snapper brand. The construction materials are selected not just for their strength but also for weather resistance, ensuring that the mowers can withstand various conditions without compromising performance. This is particularly advantageous for those who use their mowers frequently or in challenging environments.

In conclusion, Snapper's S22675 series and its associated models stand out for their powerful engines, innovative cutting deck designs, user-friendly features, and robust durability. These characteristics culminate in a mowing experience that meets the needs of a diverse range of users, from casual lawn caretakers to professional landscapers, making them a trusted choice in outdoor power equipment.
Top Page Image Contents