Snapper RZT20440BVE2, RZT22500BVE2 manual Transmission Drive Belt Replacement, Battery Charging

Page 31

Troubleshooting, Adjustments, & Service

TRANSMISSION DRIVE BELT REPLACEMENT

1.Park the rider on a smooth, level surface such as a concrete floor. Disengage the PTO, lock the motion control levers into their neutral locked positions, turn off the engine, and remove the ignition key.

2.Remove the mower belt from the PTO pulley (see MOWER BELT REPLACEMENT for instructions).

3.Relieve tension on the transmission belt (A, Figure 33a) by moving the idler arm (E) in the direction indi- cated by the curved arrow, and remove the old belt from the crankshaft and transmission pulleys.

4.Loosen (do not remove) the anti-rotation bracket hardware (C, Figure 33a), and slip the old belt out between the anti-rotation pin (B) and the PTO (A).

Note: The PTO wiring harness must be disconnected from the main wiring harness in order to remove and replace the transmission belt. Be sure to reconnect the harness after the belt is replaced.

CB

A

Figure 33a. Anti-Rotation Bracket (View Looking Back from Mower Deck)

A.PTO Clutch

B.Anti-Rotation Pin

C.Anti-Rotation Bracket Hardware

E

 

F

C

C

 

D

 

A

FRONT

 

B

 

Figure 33b. Transmission Drive Belt Replacement (Shown from Below; Components Removed for Clarity)

A.Transmission Drive Belt

B.Crankshaft Pulley

C.Transmission Pulley (2)

D.Idler Pulley

E.Idler Arm

F.Idler Tension Spring

5.Reversing steps 3-4, install the new belt, following the routing in Figure 33b. Make sure the V-side of the belt runs in the grooves of the crankshaft pulley and transmission pulleys (B & C). Also, make sure that the anti-rotation pin (B, Figure 33a) is inserted into the anti-rotation slot on the PTO before tightening hardware (C).

6.Reinstall the PTO drive belt.

BATTERY CHARGING

A dead battery or one too weak to start the engine may be the result of a defect in the charging system or other electrical component. If there is any doubt about the cause of the problem, see your dealer. If you need to replace the battery, follow the steps under Cleaning the Battery & Cables in the Regular Maintenance Section.

To charge the battery, follow the instructions provided by the battery charger manufacturer as well as all warnings included in the safety rules sections of this book.

Remove the battery from the rider and place on a level, non-concrete surface. Charge the battery at 6-10 amps for 1 hour. Do not charge at a rate higher than 10 amps.

WARNING

Keep open flames and sparks away from the battery; the gasses coming from it are highly explosive. Ventilate the battery well during charging.

30

Page 30 Page 32
Image 31
Page 30 Page 32
Contents OPERATOR’S Manual Table of Contents Safety Rules & Information From Previous Safety Rules and InformationTowing Simplicity Identification NumbersSnapper ModelsSafety Decals Safety DecalsOperational Safety Checks Safety Interlock SystemMotion Control Levers Control FunctionsChoke Features & Controls Checks Before Starting General Operating SafetyMowing OperationStarting the Engine Stopping the Rider & EngineReverse Travel Practice Zero Turn Driving PracticeSmooth Travel Forward Travel PracticeExecuting an End-Of-Row Zero Turn Practice Turning Around a CornerAttaching a Trailer Mower Removal InstallationRemoval Installation Before Every Spring Each Hours 100 250 Fall Use Regular MaintenanceLubrication Regular MaintenanceServicing the Mower Blades Service Interval Every 10 Hours or As RequiredFuel Filter Engine MaintenanceCheck Tire Pressures Checking / Adding FuelCleaning the Battery and Cables Battery MaintenanceStorage Troubleshooting the Rider Troubleshooting, Adjustments, & ServiceTroubleshooting the Mower Troubleshooting, Adjustments, & ServiceSeat Position Adjustment Seat AdjustmentsMotion Control Lever Adjustment Speed Balancing AdjustmentCutting Height Adjustment Motion Control Lever Friction AdjustmentRoller BAR Adjustment Neutral Adjustments Front Suspension Adjustment Select Models Parking Brake AdjustmentBrake Adjustment Blade Brake Check PTO Clutch AdjustmentOrient Blades Side-to-Side Mower Deck LevelingRoller BAR Leveling Deck Timing ROD AdjustmentIf Equipped Battery Charging Transmission Drive Belt ReplacementPRY Belts Over Pulleys Mower Belt ReplacementFuse Replacement Transmissions DimensionsEngine ChassisMaintenance Items Replacement PartsTechnical Manuals

RZT20440BVE2, RZT22500BVE2 specifications

The Snapper RZT22500BVE2 and RZT20440BVE2 are innovative riding mowers that exemplify the cutting-edge features and technologies available in modern lawn care equipment. These models are designed to enhance user experience, improve efficiency, and deliver exceptional cutting performance for residential and commercial users alike.

The Snapper RZT22500BVE2 is powered by a robust 25 HP Briggs & Stratton Intek V-twin engine. This powerful engine enables the mower to handle tough grass types and navigate challenging terrain with ease. Coupled with a 48-inch stamped steel cutting deck, this mower offers a smooth and precise cut, ensuring a professionally manicured lawn in a fraction of the time. The RZT22500BVE2 is equipped with Snapper's patented Infinite Speed Control, allowing users to adjust their speed effortlessly, making it easy to maneuver around obstacles or tackle tight corners.

On the other hand, the RZT20440BVE2 features a 20 HP Briggs & Stratton engine that provides ample power for regular mowing activities. With a slightly smaller yet equally efficient 42-inch cutting deck, this model is perfect for users with smaller properties or tighter spaces. The RZT20440BVE2 also boasts Instant Response Control, making it incredibly user-friendly by offering smooth transitions in speed and direction.

Both models incorporate the latest in technology to enhance the mowing experience. The dual hydrostatic transmission system in these riding mowers delivers seamless control, allowing users to drive forward or reverse with ease, without compromising power. An ergonomic seat design provides comfort during extended mowing sessions, reducing fatigue.

Additionally, both models come with a clean-out port, enabling easy maintenance of the cutting deck by allowing users to wash grass clippings away after each use. They also feature durable, heavy-duty construction, ensuring longevity and reliability in various weather conditions.

In conclusion, the Snapper RZT22500BVE2 and RZT20440BVE2 are excellent choices for lawn care enthusiasts looking for powerful, efficient, and user-friendly riding mowers. With their advanced features and reliable performance, these models stand out in the market, making lawn maintenance easier and more enjoyable. Whether you opt for the power of the RZT22500BVE2 or the compact efficiency of the RZT20440BVE2, both offer outstanding value and superior performance for all your mowing needs.
Top Page Image Contents