Snapper RT Series Safety Rules & Information, Safe Handling of Gasoline, Service & Maintenance

Page 5

Safety Rules & Information

SERVICE AND MAINTENANCE

Safe Handling of Gasoline

1.Extinguish all cigarettes, cigars, pipes, and other sources of ignition.

2.Use only approved gasoline containers.

3.Never remove the gas cap or add fuel with the engine running. Allow the engine to cool before refueling.

4.Never fuel the machine indoors.

5.Never store the machine or fuel container where there is an open flame, spark, or pilot light such as near a water heater or other appliance.

6.Never fill containers inside a vehicle or on a truck bed with a plastic bed liner. Always place containers on the ground away from your vehicle before filling.

7.Remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this is not possi- ble, then refuel such equipment on a trailer with a portable container, rather than from a gasoline dis- penser nozzle.

8.Keep nozzle in contact with the rim of the fuel tank or container opening at all times until fueling is com- plete. Do not use a nozzle lock-open device.

9.If fuel is spilled on clothing, change clothing immedi- ately.

10.Never over fill the fuel tank. Replace gas cap and tighten securely.

11.Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive.

12.If fuel is spilled, do not attempt to start the engine but move the machine away from the area of spillage and avoid creating any source of ignition until fuel vapors have dissipated.

13.Replace all fuel tank caps and fuel container caps securely.

Service & Maintenance

1.Maintain or replace safety and instruction labels as necessary.

2.Never run the unit in an enclosed area where carbon monoxide fumes may collect.

3.Keep nuts and bolts, especially blade attachment bolts, tight and keep equipment in good condition.

4.Never tamper with safety devices. Check their proper operation regularly and make necessary repairs if they are not functioning properly.

5.Keep unit free of grass, leaves, or other debris build- up. Clean up oil or fuel spillage.

6.Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.

7.Never make adjustments or repairs with the engine running unless specified otherwise in the engine man- ufacturer’s manual.

8.Do not remove the fuel filter when the engine is hot as spilled gasoline may ignite. Do not spread fuel line clamps further than necessary. Ensure clamps grip hoses firmly over the filter after installation.

9.Do not use gasoline containing METHANOL, gasohol containing more than 10% ETHANOL, gasoline addi- tives, or white gas because engine/fuel system dam- age could result.

10.If the fuel tank must be drained, it should be drained outdoors.

11.Replace faulty silencers/mufflers.

12.Grass catcher components are subject to wear, dam- age, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer’s recom- mended parts, when necessary.

13.Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them.

14.Check brake operation frequently. Adjust and service as required.

15.Use only factory authorized replacement parts when making repairs.

16.Always comply with factory specifications on all set- tings and adjustments.

17.Only authorized service locations should be utilized for major service and repair requirements.

18.Never attempt to make major repairs on this unit unless you have been properly trained. Improper ser- vice procedures can result in hazardous operation, equipment damage and voiding of manufacturer’s warranty.

19.On multiple blade mowers, take care as rotating one blade can cause other blades to rotate.

20.Do not change engine governor settings or over- speed the engine. Operating the engine at excessive speed can increase the hazard of personal injury.

21.Disengage drive attachments, stop the engine, remove the key, and disconnect the spark plug wire(s) before: clearing attachment blockages and chutes, performing service work, striking an object, or if the unit vibrates abnormally. After striking an object, inspect the machine for damage and make repairs before restarting and operating the equip- ment.

22.Never place hands near the moving parts, such as a hydro pump cooling fan, when the tractor is running. (Hydro pump cooling fans are typically located on top of the transaxle).

4

Image 5
Contents 18HP Hydro Tractors 16HP Hydro Tractors 20HP Hydro Tractors17HP Hydro Tractors Mower Decks Table of Contents Safety Rules & Information Slope Operation Safety Rules and InformationSafe Handling of Gasoline Safety Rules & InformationService & Maintenance CE Identification TAG Markings Identification NumbersNorth American ModelsSafety Decals Safety DecalsNorth American Models ALL Models CE ModelsOperational Safety Checks Safety IconsControl Functions Features & Controls Catcher Open/Close Lever General Operating SafetyAdding Fuel Stopping the Tractor & Engine Operating the TractorDriving the Tractor MowingParking Brake Function InstallationEmptying the Catcher Mulching Plug OptionalStorage Attaching a TrailerMuffler and surrounding areas may be hot Mower Deck Removal InstallationRemoving the Mower Deck Installing the Mower Deck Catcher Removal InstallationFall Before Every SpringTransmission Maintenance Regular MaintenanceBattery Maintenance Check Tire PressuresOil LubricationLubricate Rear Axle Shafts Service Interval Yearly4x4 Wood Block Servicing the Mower BladesCheck Mower Blade Timing PTO Clutch Adjustment Check Safety Interlock System CheckEngine Maintenance SET Mower Belt TensionTroubleshooting, Adjustments, & Service Troubleshooting the Mower Hopper Latch Adjustment Seat AdjustmentPitch Adjustment Seat Slide AdjustmentBrake Adjustment Steering Gear AdjustmentAdjustment Nut NutsCATCHER-FULL Alarm Adjustment Troubleshooting, Adjustment, & ServiceMower Lift Adjustment Battery ChargingAdjust PTO Clutch Window Adjustment Nut Feeler Gauge PTO Clutch AdjustmentTransmission Release Lever Transmission PurgingLeveling The Mower Mower AdjustmentsCutting Height Adjustment Arbor Drive Belt Replacement PTO Belt ReplacementEngine DimensionsTransmission ChassisMaintenance Items Replacement PartsOptional Accessories Technical Manuals

RT Series specifications

The Snapper RT Series stands out in the realm of riding lawn mowers, combining cutting-edge technology with user-friendly features to enhance lawn care. Designed for residential use, the RT Series ensures both performance and comfort, making it an ideal choice for homeowners looking for a reliable mowing solution.

One of the key features of the Snapper RT Series is its robust engine options. The mowers in this series typically come equipped with powerful engines that deliver efficient performance. Often, these engines are designed to provide easy starting and smooth operation, allowing users to tackle their mowing tasks with minimal hassle.

The RT Series showcases Snapper's patented HiVac deck technology. This unique deck design is engineered to generate superior airflow, resulting in a cleaner, more precise cut. The enhanced airflow lifts grass for a faster and more uniform mowing experience while efficiently bagging clippings. This not only ensures a well-manicured lawn but also minimizes the need for frequent clean-up.

Comfort is a priority in the Snapper RT Series design. The mowers feature an ergonomic seat and easy-to-reach controls, allowing operators to mow for extended periods without discomfort. The adjustable seat adds to this comfort, accommodating a variety of user heights and preferences.

Another notable aspect of the Snapper RT Series is its ease of maneuverability. With a tight turning radius, these mowers can navigate around obstacles with precision. This feature is particularly beneficial for homeowners with complex landscapes, gardens, or flower beds. The lightweight design, coupled with responsive steering, makes mowing under trees, around flower beds, and along fences effortless.

The Snapper RT Series also incorporates advanced safety features. With automatic brakes, blade engagement systems, and other safety mechanisms, users can be assured of a safer mowing experience. These safety technologies help protect the operator while enhancing the overall mowing process.

Durability is a hallmark of the Snapper RT Series. Built from high-quality materials, these mowers are engineered to withstand the rigors of lawn maintenance. Rust-resistant components and a sturdy frame ensure that the mower can handle tough mowing conditions, providing long-lasting reliability.

In summary, the Snapper RT Series offers a powerful combination of performance, comfort, and advanced technology. Its user-friendly design, ease of maneuverability, and robust safety features make it an exceptional choice for homeowners. Whether tending to a small or large yard, the RT Series delivers an efficient and enjoyable mowing experience.