Snapper SZT18426BVE, SZT20486BVE Service Annually, Storage OUT of Season

Page 17

Section 3 – MAINTENANCE

3.4 SERVICE - ANNUALLY

Perform all maintenance as described in the maintenance schedule.

3.4.1. Engine

Service engine according to engine owner’s manual.

3.4.2. Air Filter

Refer to engine owner’s manual for service instructions.

3.4.3. Oil Filter

Refer to engine owner’s manual for service instructions.

3.4.4. Engine Oil

Refer to engine owner’s manual for service instructions.

3.4.5. Transaxle

IMPORTANT: DO NOT try to open reservoir cap at any time. The transaxle is maintenance free. The transaxle does not require any fluid or any service. If there is any problem: leakage, malfunction or etc. return the SCRAMBLER immediately to the nearest authorized Snapper dealer for service.

3.4.6. Fuel Filter

Service fuel filter as instructed below. Close fuel valve in fuel line. Run engine until engine runs out of fuel. Turn key to “OFF” position. Engine MUST be stopped and MUST be cold before removing filter. Perform filter change only when fuel line is empty.

1.Remove hose clamps from fuel filter.

2.Remove fuel lines from filter. Discard filter.

3.Install new fuel filter. Reinstall hose clamps. See Figure 3.8.

NEW FUEL

FILTER

HOSE CLAMPS

FIGURE 3.8

3.5 STORAGE (OUT OF SEASON)

Perform the following procedures to insure the SCRAMBLER will operate properly when taken out of storage.

3.5.1.Thoroughly clean the SCRAMBLER by removing all grass clippings and debris.

3.5.2.Perform maintenance and lubrication as described in the previous sections.

3.5.3.Drain fuel from fuel tank into an approved container outdoors away from all sources of ignition.

3.5.4.Start engine and allow it to run until engine runs out of fuel. This allows the carburetor and fuel system to remain clean during storage.

3.5.5.Remove battery. Refer to Section

“BATTERY REMOVAL AND STORAGE”.

3.5.6.Close vent on fuel cap and fuel valve in fuel line. Remove key.

17

Image 17
Contents Scrambler From Previous Column Important Safety InstructionsSafe Handling of Gasoline Towing Table of Contents Nomenclature IntroductionEngine Speed & Choke Control Right Control Panel Cutting Deck Adjustment Handle Forward of Operator SeatMotion Control Levers Parking Brake Next to Left Control Panel Applies park brakeStopping Engine PRE-START Check ListEngine Operation 2.2.1. Starting Engine Getting Ready Motion ControlForward Motion Reverse MotionLeft turn shown right turn opposite Conventional TurningZERO-TURNING Stopping MotionMower Blade Engagement Mower Operation Cutting Height AdjustmentMowing Operations Mower Blade DisengagementEngine Must Begin to Stop if Engine Must not Start ifEngine should Start if Change Engine OIL Service After First 5 HoursCheck Mower Blade Twin & Triple Blade DeckCheck Transaxle Drive Belt Service Every 25 Operating HoursMower Components Service Every 25 Operating Hours 3.3.1. EngineFront Wheel Bearings Mower Deck LinkageFront Caster Wheel Pivot Shaft Parking Brake Pivot BushingsStorage OUT of Season Service AnnuallyMower Drive Belt Adjustment Engine Adjustments & RepairBelt Replacement Belt RemovalBlade Brake Refer to Section MAINTENANCE/REPLACEMENT PartsHairpin Lift ARM Twin Blade Deck Front or Rear View of DeckSingle Blade Deck Deck ShownWheel Brake Adjustment Blade Replacement Mower Blade Replacement 4.4.1. Blade Wear LimitsNumbers refer to Section Maintenance /REPLACEMENT Parts Blade SharpeningBattery Installation 1. Slide battery into battery cradle Battery Battery RemovalBattery Service Battery StorageNeutral Adjustments Battery TestingMotion Control Adjustments Motion Control Lever Alignment Neutral Return Spring AdjustmentsRight side shown fuel tank removed for clarity Corrective Action Problem Probable CauseTrouble Shooting on Next Loss Of Traction MAINTENANCE/REPLACEMENT PartsUSE HRS Season Service Performed Each100 Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Scrambler ZERO-TURN Hydro Drive Series

SZT18426BVE, SZT20486BVE specifications

The Snapper SZT18426BVE and SZT20486BVE are advanced lawn care machines designed for homeowners and professionals who demand high performance and reliability in their lawn maintenance tasks. Both models exhibit a combination of power, versatility, and user-friendly features that make them stand out in the market.

The Snapper SZT18426BVE is equipped with an 18 horsepower engine, making it a robust performer for various lawn sizes and types. Its cutting deck is 26 inches wide, which allows for efficient mowing even in tighter spaces. The SZT20486BVE takes it up a notch with a more powerful 20 horsepower engine and a wider 48-inch cutting deck, enabling it to cover more ground quickly, making it ideal for larger properties.

One notable feature of both models is the Zero-Turn technology, which allows for unmatched maneuverability. This function enables the operator to turn on a dime, facilitating access to corners and obstacles with ease. This is particularly beneficial for mowing around trees, flower beds, and other landscaping features. The comfort of the operator is also a priority; both models come with fully adjustable high-back seats that provide ample support during extended use.

Equipped with advanced cutting technologies, these Snapper models feature a patented mowing system that ensures a precise cut while maintaining the health of the grass. The adjustable cutting height offers versatility to achieve the desired grass length, accommodating various lawn conditions and preferences.

Moreover, both the SZT18426BVE and SZT20486BVE are designed with durability in mind. Their rugged frames and heavy-duty components ensure long-lasting performance, making them investments that stand the test of time. Additionally, maintenance is straightforward with easily accessible parts and a simple design that allows users to keep their machines in peak condition with minimal effort.

Safety features, such as the operator presence control, ensure that the mower will stop when the operator is not in a seated position, providing peace of mind during use. Both models also come with an easy-to-use dashboard that allows for quick adjustments on the go, including speed control and blade engagement.

Overall, the Snapper SZT18426BVE and SZT20486BVE are excellent choices for those seeking efficient, reliable, and user-friendly zero-turn lawn mowers that combine power and innovative features for a superior mowing experience.