Snapper SZT18426BVE, SZT20486BVE important safety instructions Wheel Brake Adjustment

Page 22

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blade running. STOP blade. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.2.9.MOWER DECK ADJUSTMENT (LEVELNESS) (Continued From Previous Page)

2. Front to Rear Deck Pitch (42” Decks)

With the SCRAMBLER on a smooth, level surface, rotate blades until blade tips are at front and rear of deck. Measure the distance from blade tips to floor. The distance should be the same, or the rear 1/4” higher than the front. If the rear blade tip is lower or is more than 1/4” higher than the front, proceed with adjustment.

a.Remove rear hanger chains.

b.Turn each hanger pivot the same number of rotations on the eye-bolt to raise or lower the rear of the deck. See Figure 4.8.

c.Reinstall rear hanger chains and measure blade tips again.

d.Repeat steps “a” through “c” until proper levelness is obtained.

X

X + 1/4”

FRONT

REAR

ROTATE HANGER PIVOT:

UP TO RAISE DECK OR

DOWN TO LOWER DECK.

ADJUSTING

 

NUT

DO NOT ADJUST

TIMING

ROD

42” DECK SHOWN

FIGURE 4.9

4.3WHEEL BRAKE ADJUSTMENT

Adjust the wheel brake if wheels turn when parking brake is engaged. Adjust the wheel brake by turning wheel brake adjusting nut clockwise to increase braking action or counter clockwise to decrease braking action. See Figure 4.10.

ADJUST

UNDERSIDE VIEW OF MACHINE

COUNTER-

 

CLOCKWISE TO

 

DECREASE

 

BRAKE

 

ADJUST

 

CLOCKWISE TO

 

INCREASE

 

BRAKE

 

WHEEL

ELECTRIC

CLUTCH

BRAKE ROD

 

 

 

FIGURE 4.10

FIGURE 4.8

4.2.10.MOWER DECK TIMING ROD - 42” DECKS The mower deck timing rod is preadjusted at the factory. It is set to maintain the deck in the same attitude through all heights of cut. If the timing rod requires adjustment, contact an authorized SNAPPER dealer for service. See Figure 4.9.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Scrambler Important Safety Instructions From Previous ColumnSafe Handling of Gasoline Towing Table of Contents Introduction NomenclatureMotion Control Levers Cutting Deck Adjustment Handle Forward of Operator SeatEngine Speed & Choke Control Right Control Panel Parking Brake Next to Left Control Panel Applies park brakeEngine Operation 2.2.1. Starting Engine PRE-START Check ListStopping Engine Forward Motion Motion ControlGetting Ready Reverse MotionZERO-TURNING Conventional TurningLeft turn shown right turn opposite Stopping MotionMowing Operations Mower Operation Cutting Height AdjustmentMower Blade Engagement Mower Blade DisengagementEngine should Start if Engine Must not Start ifEngine Must Begin to Stop if Check Mower Blade Service After First 5 HoursChange Engine OIL Twin & Triple Blade DeckService Every 25 Operating Hours Check Transaxle Drive BeltService Every 25 Operating Hours 3.3.1. Engine Mower ComponentsFront Caster Wheel Pivot Shaft Mower Deck LinkageFront Wheel Bearings Parking Brake Pivot BushingsService Annually Storage OUT of SeasonBelt Replacement Engine Adjustments & RepairMower Drive Belt Adjustment Belt RemovalRefer to Section MAINTENANCE/REPLACEMENT Parts Blade BrakeHairpin Lift ARM Single Blade Deck Front or Rear View of DeckTwin Blade Deck Deck ShownWheel Brake Adjustment Numbers refer to Section Maintenance /REPLACEMENT Parts Mower Blade Replacement 4.4.1. Blade Wear LimitsBlade Replacement Blade SharpeningBattery Service Battery Battery RemovalBattery Installation 1. Slide battery into battery cradle Battery StorageMotion Control Adjustments Battery TestingNeutral Adjustments Right side shown fuel tank removed for clarity Neutral Return Spring AdjustmentsMotion Control Lever Alignment Trouble Shooting on Next Problem Probable CauseCorrective Action MAINTENANCE/REPLACEMENT Parts Loss Of Traction100 Service Performed EachUSE HRS Season Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Scrambler ZERO-TURN Hydro Drive Series

SZT18426BVE, SZT20486BVE specifications

The Snapper SZT18426BVE and SZT20486BVE are advanced lawn care machines designed for homeowners and professionals who demand high performance and reliability in their lawn maintenance tasks. Both models exhibit a combination of power, versatility, and user-friendly features that make them stand out in the market.

The Snapper SZT18426BVE is equipped with an 18 horsepower engine, making it a robust performer for various lawn sizes and types. Its cutting deck is 26 inches wide, which allows for efficient mowing even in tighter spaces. The SZT20486BVE takes it up a notch with a more powerful 20 horsepower engine and a wider 48-inch cutting deck, enabling it to cover more ground quickly, making it ideal for larger properties.

One notable feature of both models is the Zero-Turn technology, which allows for unmatched maneuverability. This function enables the operator to turn on a dime, facilitating access to corners and obstacles with ease. This is particularly beneficial for mowing around trees, flower beds, and other landscaping features. The comfort of the operator is also a priority; both models come with fully adjustable high-back seats that provide ample support during extended use.

Equipped with advanced cutting technologies, these Snapper models feature a patented mowing system that ensures a precise cut while maintaining the health of the grass. The adjustable cutting height offers versatility to achieve the desired grass length, accommodating various lawn conditions and preferences.

Moreover, both the SZT18426BVE and SZT20486BVE are designed with durability in mind. Their rugged frames and heavy-duty components ensure long-lasting performance, making them investments that stand the test of time. Additionally, maintenance is straightforward with easily accessible parts and a simple design that allows users to keep their machines in peak condition with minimal effort.

Safety features, such as the operator presence control, ensure that the mower will stop when the operator is not in a seated position, providing peace of mind during use. Both models also come with an easy-to-use dashboard that allows for quick adjustments on the go, including speed control and blade engagement.

Overall, the Snapper SZT18426BVE and SZT20486BVE are excellent choices for those seeking efficient, reliable, and user-friendly zero-turn lawn mowers that combine power and innovative features for a superior mowing experience.
Top Page Image Contents