Snapper ZMT2500KH, ZM5201M, ZM6101M After Every 25 Operating Hours 3.3.1. Engine

Page 11

Section 3 - MAINTENANCE

3.2.3.CHECK MOWER DRIVE BELT 1. Foot Rest Removal

a.Lower deck to lowest setting.

b.Remove foot rest. See Figure 3.3.

c.Removal of foot rest will allow access to deck belt.

LIFT FOOT

REST UP & OFF

POWER UNIT

FRAME TO GAIN

ACCESS TO

MOWER BELT

FIGURE 3.3

2. Checking Belt Tension

The idler and spring provide proper belt tension and require no adjustment. If belt is frayed, slit, severed or belt strands exposed, replace belt before operating mower.

3.3AFTER EVERY 25 OPERATING HOURS 3.3.1. ENGINE

1. Engine Oil

Change engine oil. Refer to Section “CHANGE ENGINE OIL”. Refer to engine owner’s manual for oil specifications.

2. Air Filter

Refer to engine owner’s manual for service instructions.

3.3.2.MOWER COMPONENTS 1. Mower Drive Belt

No adjustment required. Replace belt as needed.

2. Mower Blade

Check blade for sharpness, wear, damage, and torque. Refer to Section “MOWER BLADE REPLACEMENT”.

3. Mower Deck Levelness

Check mower deck for proper levelness. Adjust as required. Refer to Section “MOWER DECK ADJUSTMENT – LEVELNESS”.

4. Clean Mower Deck

a. Remove key from ignition switch.

b. Remove spark plug wire(s) and secure away from spark plug(s).

c.Raise mower deck to its highest setting. It may be necessary to raise mower deck higher using a hydraulic floor jack. Secure machine with safety blocks.

d.Clean underside of mower deck, removing all accumulation of grass clippings and debris.

e.Clean top of deck, removing all grass clippings and debris.

5. Mower Blade Spindle - Lubrication

a.Remove foot rest.

b.Remove foot rest to gain access to lubrication fitting located on the top of deck below deck pulleys. Lubricate with Kendall NLGI No. 2 lithium grease or equivalent, from a grease gun until grease purges from vent located on spindle housing underneath deck. See Figure 3.4.

LUBRICATE

SPINDLE

ASSEMBLIES

FIGURE 3.4

6. Mower Deck Linkage - Lubrication

Lubricate all mower deck linkage pivot points with a light coat of motor oil.

WARNING

DO NOT attempt any maintenance, adjustments or service with engine running. STOP engine. STOP blades. Set brake. Remove key. Remove spark plug wires and secure away from spark plugs. Engine and components are HOT. Avoid serious burns, allow sufficient time for all parts to cool.

11

Image 11
Contents Mower Unit Model Number ExplanationPreparation Protection for ChildrenProtection Against Tipovers Mount and dismount machine from left side MaintenanceOperation Table of Contents Nomenclature IntroductionPRE-START Check List Operating InstructionsStarting Mower Blades Starting & Stopping ENGINE, BLADES, Parking BrakeStarting Engine Stopping EngineParking Brake Stopping Machine Cutting Height AdjustmentOPERATION- Motion Controls 2.4.1. Driving Machine Check Mower Blade Service After First 5 HoursChange Engine OIL After Every 25 Operating Hours 3.3.1. Engine Annually END of Each Season Other Lubrication PointsBefore Operating Machine Deck Removal Annually END of Each Season from previousFuel Filter Deck Removal from previous Power Transfer Shaft RemovalSide to Side Level Neutral Position AdjustmentsFront to Rear Level Mower Deck Adjustment LevelnessMower Blade Replacement 4.5.1. Blade Wear Limits Parking Brake AdjustmentEngine Adjustments & Repair Belt Removal Mower Drive Belt ReplacementBelt Replacement Blade SharpeningBattery Service Battery Battery RemovalBattery Installation Do not Overfill Battery TestingNEW Battery Preparation 1. Remove battery from carton Trouble Shooting on Next Problem Probable Cause Corrective ActionTractor Will Not Move 100 MAINTENANCE/REPLACEMENT Parts Mower DeckService Performed Each MAINTENANCE/REPLACEMENT PartsDisclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Page Page Page MID Mount Z-RIDER Zero Turning Hydro Drive Series